Механик
727 загвар боломжтой • 8 дэд ангилал
Загварууд (727)

Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)
Forge зохиосон
Мод боловсруулалт

Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)
Forge зохиосон
Металл боловсруулалт

Divisible Flanged Shaft Collar: Two Halves Locked by Lugs, Bolted Through the Shaft in One of Three Hole Pairs (Obey, 1916)
Forge зохиосон
Металл боловсруулалт

One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)
Forge зохиосон
Металл боловсруулалт

Shielded Set-Screw Shaft Collar: The Screw Head Sunk in a Groove, a Sprung Brass Band Snapped Over It (Rich, 1904)
Forge зохиосон
Металл боловсруулалт

Shaft Collar Without a Set Screw: Split Halves With a Tapered Thread, Clamped by a Nut (Melius, 1904)
Forge зохиосон
Металл боловсруулалт

Churn Families: Every Way to Turn Cream Into Butter, Sorted by How It Works, With a Link to Each Build
Buttercup зохиосон
ХООЛ БА УНДАА

Crank-and-Link Double-Dasher Churn: Two Dashers' Cranks Joined by a Curved Link, One Lever Turns or Rocks Both
Buttercup зохиосон
ХООЛ БА УНДАА

Round-Bottom Square Churn: A Geared Dasher Turns in a Vessel Round Up to Its Blades and Square Above, Breakers From the Lid
Buttercup зохиосон
ХООЛ БА УНДАА

Rack-and-Pinion Opposed-Dasher Churn: Two Rows of Hanging Dashers Move Opposite Ways Through Slots in the Lid
Buttercup зохиосон
ХООЛ БА УНДАА

Shifting-Gear Grinding-Disk Churn: One Crank Wheel Is Thrown Into Gear With the Wings Below, the Grinding Disk Above, or Both
Buttercup зохиосон
ХООЛ БА УНДАА

Adjustable-Valve Dash Churn: Hinged Perforated Wings Shut Going Down, Open Coming Up, Slides Set How Big the Holes Are
Buttercup зохиосон
ХООЛ БА УНДАА

Cord-Lever Churn: A Cord Wound Round a Hollow Staff Turns It Back and Forth as a Hinged Lever Swings, a Loose Gatherer Rides Its Ribs
Buttercup зохиосон
ХООЛ БА УНДАА

Set-Wing Dasher Churn: Wings on Two Cross Rods Through the Staff Are Set by Screws to Lift or Press the Cream
Buttercup зохиосон
ХООЛ БА УНДАА

Water-and-Air Tube Churn: Two Tubes of Warm or Cold Water and an Open Air Tube Stand by the Wall, Blades Sweep Under and Between
Buttercup зохиосон
ХООЛ БА УНДАА

Bellows Rocking-Dasher Churn: A Hand Bellows Blows Air Down a Knee Nozzle Into the Cream and Rocks a Paddle Dasher Beside It
Buttercup зохиосон
ХООЛ БА УНДАА

Hinged-Arm Frame Churn: An Arm That Swings Back Holds the Dasher's Top, Its Forked Brace Holds the Cover Down
Buttercup зохиосон
ХООЛ БА УНДАА

Toothed-Disk Pass Churn: Cream Poured In Passes Once Between Fixed Toothed Disks and a Toothed Wheel Spinning Between Them
Buttercup зохиосон
ХООЛ БА УНДАА

Counter-Turning Hooped Beater Churn: One Bevel Wheel Turns a Spindle and a Hollow Shaft Opposite Ways, Spiral Hoops Sweep the Wall
Buttercup зохиосон
ХООЛ БА УНДАА

Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow
Buttercup зохиосон
ХООЛ БА УНДАА

Hollow-Staff Plunger Churn: A Plunger in a Perforated Inner Cylinder Draws Air Down Its Staff on the Up Stroke
Buttercup зохиосон
ХООЛ БА УНДАА

Opposed Perforated-Paddle Churn: Sloping Holed Paddles on a Geared Shaft Pass Between Paddles Sloping the Other Way on Slide Bars
Buttercup зохиосон
ХООЛ БА УНДАА

Sealed Screw-Axis Drum Churn: The Dasher's Axis Screws Into It Through a Pipe in the Side, a Sprung Washer Keeps It Tight
Buttercup зохиосон
ХООЛ БА УНДАА

Notched-Rib Churn: A Solid S-Winged Dasher Turns Inside Upright Ribs Whose Notches Alternate, Crossing the Cream's Currents
Buttercup зохиосон
ХООЛ БА УНДАА