IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Propeller-and-Spoon Egg Beater: Spoon Arms Break the Swirl
A turning beater soon sets the whole liquid circling with it.
William T. Nicholson of Providence, Rhode Island, received US 32,886, dated 23 July 1861, for an egg beater: a crank wheel with bevelled face teeth turns a pinion and a pair of propeller blades; under the pinion a disk with an elliptic groove rocks two arms ending "in the form of a spoon bill's beak," so "the circling currents occasioned by the blades of the propeller will be broken at regular intervals." It clamps into a socket on a table or lifts out for use by hand.
This rung works out the stroke rates, then prints the crown wheel, pinion, cam and propeller, builds the frame and arms, and times a beating.
Ilọsíwájú
About 5 hours, plus printing
Ìlànà
1
1
Stroke rates
Stroke rates
Ń ṣí ìwé Jupyter…
2
2
A crank wheel and pinion before it
A crank wheel and pinion before it
The embedded blueprint drives two beaters off one wheel. Nicholson drives a propeller and lets a cam rock two spoon arms against its swirl.
3
3
Read US 32,886
Read US 32,886
"To the under side of the pinion E is secured the disk H (Fig. 5,) its lower surface being furnished with an elliptic groove or channel I. Two arms K K pivoted to the handle at c and d extend to the bottom of the propeller blade their lower extremities being in the form of a spoon bill's beak. A projecting ear e, e on each arm is inserted in the elliptic groove I whereby as the propeller shaft F is rotated to which the disk is attached a reciprocating motion is given to each of the arms."
4
4
Print the gears, cam and propeller
Print the gears, cam and propeller
Print the 48-tooth crown wheel (/uploads/blueprints/propeller-spoon-egg-beater-crown-wheel.stl), the 12-tooth pinion (/uploads/blueprints/propeller-spoon-egg-beater-pinion.stl), the cam disk with its elliptic groove (/uploads/blueprints/propeller-spoon-egg-beater-cam.stl) and the propeller (/uploads/blueprints/propeller-spoon-egg-beater-propeller.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Okùn PETG1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ẹ̀rọ ìtẹ̀ 3D oníwàyà (FDM)5
5
Frame and wheel
Frame and wheel
Cut a plywood handle frame. Bolt the crown wheel to it on an M5 screw with a crank near its rim, and drill a bearing for the propeller shaft so the pinion meshes the wheel's face.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Àwo igi tí a lẹ̀ pọ̀1 ẹyọ
Skurú ẹ̀rọ1 ẹyọ
Wáṣà Pẹrẹsẹ1 ẹyọ
Nọ́ọ̀tì Onígun Mẹ́fà1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Kópìngì
Ẹ̀rọ Ìlùkòkò Aláìlókùn
Àkójọ Orí Ìlùkòkò
Kọ́kọ́rọ́ tí a lè ṣàtúnṣe6
6
Shaft, cam and propeller
Shaft, cam and propeller
Epoxy the pinion, then the cam under it, on a 5 mm rod through the bearing, and the propeller on the rod's foot.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ọ̀pá Róbótó Irin Rírọ̀1 ẹyọ
Ẹpọ́ksì Ẹ̀yà Méjì1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Irin
Ìdìmú Tábìlì7
7
Spoon arms
Spoon arms
Bend two arms of stainless wire with a spoon-shaped flat at the foot. Pivot each on a screw in the frame either side of the shaft, and bend a short ear on each into the cam's groove.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Okùn irin aláìjẹrùn1 ẹyọ
Ìsúrù igi #8 x 1"1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ẹ̀mú Olórí Yíká
Ẹmú Ẹnu Pẹrẹsẹ
Ìṣù àwọn ohun ìyí skurú
Òṣùwọ̀n Kálípà Díjítà Ìnṣì 68
8
The patent drawing
The patent drawing
US 32,886 drawing sheet, public domain (expired patent).
9
9
With and without the arms
With and without the arms
Beat two egg whites with the arms in the groove and time them to stiff peaks; lift the ears out and repeat with the propeller alone.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ẹyin4 ẹyọÀwọn irinṣẹ́ tí a nílò:
Àwo ìdàpọ̀ ńlá ti irin tí kò ń yá
Aago Ìdúró10
10
Arms that jam, a cam that throws them
Arms that jam, a cam that throws them
Propeller-and-spoon egg beater troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**William T. Nicholson** of Providence, Rhode Island, received US 32,886, dated 23 July 1861. The grooved disk is set with its longest diameter in the same plane as the propeller blades, so the arms clear the blades; the socket or chair fixes to a table by spurs and one wood screw, its inclined sides grasping the handle, which can be lifted out for use by hand. He claimed the reciprocating beaters combined with a revolving beater.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A crown wheel and spur pinion stand in for his bevelled wheel, and a plywood frame for his handle and socket. Your times are the result.
Àwọn ohun-èlò
10- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- Àyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 4 ẹyọÀyè
Àwọn irinṣẹ́ tó nílò
13- Àyè
- 1 vendor sell this, none ship to you yetÀyè
- Àyè
- Àyè
- Àyè
Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways
láti ọwọ́ Martin
OÚNJẸ ÀTI OHUN MÍMU
29
0
0
0
0
0
Twisted-Strip Egg Beater: Faces Beat and Edges Cut
láti ọwọ́ Martin
OÚNJẸ ÀTI OHUN MÍMU
33
0
0
0
0
0
Piston-Pump Egg Beater: Pump the Eggs Through a Grate
láti ọwọ́ YourGrandma
OÚNJẸ ÀTI OHUN MÍMU
24
0
0
0
0
0
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.