IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀

The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It
A plunger pressed straight down by the hand needs a strong push to empty a lemon.
A. Clarence Weeks of New York received US 165,638, dated 13 July 1875, for a squeezer with a frame on legs over a dish, a perforated bowl in the frame, a plate hinged to one end carrying the plunger, two standards on the frame with a shaft across them carrying "a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger", and springs from the plate to the standards. "By the use of the cam-lever an immense power is obtained, and the juice is extracted from the lemon in a more thorough and perfect manner than when the power is applied directly to the plate or bar carrying the plunger."
This rung works out the cam's average force, with a work check, then builds the frame, the hinged plate and the cam lever in hardwood and steel, and squeezes lemons with it.
Àárín
About 5 hours
Ìlànà
1
1
The cam's force
The cam's force
Ń ṣí ìwé Jupyter…
2
2
A lever press before it
A lever press before it
The embedded blueprint presses the lemon with the lever itself. Weeks puts a cam lever over a hinged plate, so a turn of the lever gives a far greater push.
3
3
Read US 165,638
Read US 165,638
"Two standards, E E, are attached to the frame A, one on each side, in the upper portions of which standards are bearings for a shaft, f, to which is attached, midway of its length, a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger. J is a spring, which may be of rubber or metal, having its lower end attached to the board or plate C, and its upper end attached to the standard E."
"When the cam-lever G is depressed its face or bearing-surface presses upon the board or plate C, and forces the plunger into the bowl upon the lemon."
4
4
Build the squeezer and press lemons
Build the squeezer and press lemons
**Frame and bowl.** Make a hardwood board frame on four legs, tall enough for a dish beneath, with a hole in it. Fit a tin-can bowl with a punched base into the hole.
**Plate and plunger.** Hinge a hardwood plate to one end of the frame with a butt hinge, and screw a hardwood plunger to its underside so it enters the bowl.
**Standards and cam.** Screw two hardwood standards to the frame's sides beside the plate and run a steel rod across between them as the shaft f. Cut a hardwood cam lever with a curved face whose distance from the shaft grows by about 15 mm over 60° of turn, drill it for the shaft, and fix it in the middle of the rod with a pin.
**Springs.** Hook two extension springs from the plate to the standards so they lift the plate when the cam is raised.
**Test.** Put a half lemon in the bowl over a dish and press the lever down. Compare the juice with a half pressed by pushing the plate down by hand.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Pátákó Igi Líle2 ẹyọ
Ìṣù Igi Líle2 ẹyọ
Èèkàn igi0.6 mítà
Ìṣó igi16 ẹyọ
Ìdìpọ̀ Igi1 ẹyọ
Ìgò irin1 ẹyọ
Ìdìmú ẹnu-ọ̀nà1 ẹyọ
Ọ̀pá Róbótó Irin Rírọ̀0.2 mítà
Ìṣó2 ẹyọ
Orísun ìfà2 ẹyọ
Lẹ́mọ́ọ̀nù3 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Ọwọ́
Ìdìpọ̀ àyà igi
Ayùn
Ẹ̀rọ Ìlùkòkò Aláìlókùn
Àkójọ Orí Ìlùkòkò
Ìlàǹkàn irin
Òòlù
Ìṣù àwọn ohun ìyí skurú
Ayùn Irin
Ọ̀bẹ ilé ìdáná
Òṣùwọ̀n Díjítà Ilé Ìdáná
Ìbọ̀wọ́ Iṣẹ́ Awọ5
5
A cam that slips, jams or does not lift
A cam that slips, jams or does not lift
Cam-lever lemon squeezer troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**A. Clarence Weeks** of New York, New York, filed US 165,638 on 26 April 1875; it is dated 13 July 1875. His frame A had feet or legs a, the bowl B had perforations b, the plate C was hinged to one end of the frame, and there could be one spring or two. His claim is the frame with the perforated bowl and standards, the pivoted plate with its plunger, the springs, and the shaft with its cam lever.
**Honest limits.** Hardwood, a tin bowl and a steel rod stand in for his parts. The notebook gives the average force without friction; its forces, lengths and angles are examples. Your juice is the result.
Àwọn ohun-èlò
11- 2 ẹyọÀyè
- 2 ẹyọÀyè
- 0.6 mítàÀyè
- 16 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 0.2 mítàÀyè
- 2 ẹyọÀyè
- 2 ẹyọÀyè
- 3 ẹyọÀyè
Àwọn irinṣẹ́ tó nílò
12- Àyè
- Àyè
- 1 vendor sell this, none ship to you yetÀyè
- Àyè
- Àyè
- Àyè
Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà

The Ring-Set Lemon Squeezer: A Bowl Held in Its Handle by a Screwed Ring
láti ọwọ́ YourGrandma
Iṣẹ́ Igi
28
0
0
0
0
0

The False-Bottom Lemon Press: A Hinged Lever Over a Die, and One Hole for the Juice
láti ọwọ́ TheChef
Iṣẹ́ Igi
18
0
0
0
0
0

The Clamp-Frame Lemon Squeezer: A Screw Press That Clamps to the Table
láti ọwọ́ Forge
Iṣẹ́ Irin
22
0
0
0
0
0
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.
