SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
S-Dasher Friction-Board Churn: A Double-Curved Dasher Throwing Cream Over Grooved Boards
The Walkers lined a square churn with grooved boards so the cream would be thrown against them "thus keeping up a constant friction on all sides."
William Walker and Matthew C. Walker of Lancaster, Pennsylvania, received US 7,554, dated 6 August 1850, for a square water-tight box about fourteen inches each way holding about 40 quarts, half filled, with a "double curved or S shaped dasher" revolving in the centre by a crank and a thumb screw. Four grooved cross pieces run along each side of its curved ends; a friction board grooved underneath inclines across the top; a triangular board returns the cream onto it; a grooved friction piece sits in the lower right corner.
This rung checks the box's capacity, then prints the S dasher, friction boards and corner piece, fits them in a box, and makes butter.
Katamtaman
About 4 hours, plus printing
Mga Tagubilin
1
1
Capacity
Capacity
Naglo-load ng Jupyter notebook…
2
2
A shaped dash in a box churn before it
A shaped dash in a box churn before it
The embedded blueprint twists its wings into a screw. The Walkers bend theirs into an S and add grooved boards round the box for friction.
3
3
Read US 7,554
Read US 7,554
"As the churn is put in operation, the cream is thrown against the grooves of the incline board E, dashed around and under it, and passed over and against the friction piece G, in the right hand corner of box, while the ends of the dasher H and wide cross piece N keep the cream continually dashing against the grooves of the incline board E thus keeping up a constant friction on all sides."
4
4
Print the parts
Print the parts
Print the S dasher with its four grooved cross pieces in one piece (/uploads/blueprints/s-dasher-friction-board-churn-s-dasher.stl), the grooved incline board (/uploads/blueprints/s-dasher-friction-board-churn-incline-board.stl), the grooved corner piece (/uploads/blueprints/s-dasher-friction-board-churn-corner-piece.stl) and the crank arm (/uploads/blueprints/s-dasher-friction-board-churn-crank-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Mga materyales para sa hakbang na ito:
PETG filament1 pirasoMga kailangang kasangkapan:
Limbagang 3D na FDM5
5
Fit the box
Fit the box
Take a food-safe box about 180 mm each way. Glue the incline board across the top, sloping down to within 20 mm of the left side, grooves underneath, and a triangular plywood board on that side to turn the cream back onto it. Glue the corner piece in the lower right corner. Drill both ends on the centre for the dasher's shaft.
Mga materyales para sa hakbang na ito:
Sisidlan ng imbakan na antas pagkain1 piraso
Plantsa ng playwud1 piraso
Silicone Sealant1 pirasoMga kailangang kasangkapan:
Lagaring Pangkurba
Walang-Kableng Barena
Hanay ng Talim ng Barena
Mga clamp6
6
Dasher and crank
Dasher and crank
Pass a 10 mm square hardwood shaft through the box and the dasher, glue the crank arm and a dowel handle on one end, and hold the other with a thumb screw through a washer, as theirs. Cut an air hole in the lid.
Mga materyales para sa hakbang na ito:
Mga tarugong matigas na kahoy1 piraso
Mga turnilyo ng makina1 piraso
Patag na Sinturon1 piraso
Pandikit sa Kahoy1 pirasoMga kailangang kasangkapan:
Lagaring PangkamayWalang-Kableng Barena
Set ng mga distornilyador7
7
The patent drawing
The patent drawing
US 7,554 drawing sheet, public domain (expired patent).
8
8
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Fill the box half full, about 2.9 litres. Crank steadily; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Mga materyales para sa hakbang na ito:
Makapal na krema2900 ml
Magaspang na Asin sa Dagat1 piraso
Tubig1 pirasoMga kailangang kasangkapan:
Termometro na naiiwang nakatusok
Panukat ng Oras
Digital na Timbangang Pangkusina
Malaking mangkok na panghalo na asero na hindi kinakalawang9
9
Dasher that strikes, cream that escapes
Dasher that strikes, cream that escapes
S-dasher friction-board troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**William Walker and Matthew C. Walker** of Lancaster, Pennsylvania, received US 7,554, dated 6 August 1850. Their box was of inch boards; a ledge at the top confined the lid, with a projecting strip on its underside to close it tight, and an aperture M let the air through. They claimed the double-curved S-shaped dasher with the grooved pieces.
**Honest limits.** A food-safe box and printed parts stand in for their wooden churn, at about a third of its size. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Mga Materyales
11- 1 pirasoPlaceholder
- Placeholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 2900 mlPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
Mga Kinakailangang Kasangkapan
11- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
Quarter-Twist Spiral Dash Churn: Wings Twisted Between Arms Set at Right Angles
ni Woody
Paggawa ng Kahoy
16
0
0
0
0
0
Butter-Strainer Churn: Cream Thrown Into a Strainer That Keeps the Butter
ni TheChef
PAGKAIN AT INUMIN
38
0
0
0
0
0
Shaftless Dasher-Wheel Churn: Bevelled Buckets Drive the Cream to the Centre
ni Martin
PAGKAIN AT INUMIN
34
0
0
0
0
0
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.