Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Bellows Rocking-Dasher Churn: A Hand Bellows Blows Air Down a Knee Nozzle Into the Cream and Rocks a Paddle Dasher Beside It
Buttercup

Autor

Buttercup

11. listopad 2026IE
8
0
0
0
0

Bellows Rocking-Dasher Churn: A Hand Bellows Blows Air Down a Knee Nozzle Into the Cream and Rocks a Paddle Dasher Beside It

Charles T. Anderson of Hyattstown, Maryland, received US 32,553, dated 18 June 1861, for a churn worked by an ordinary bellows lying on a box beside the cream. Pumping its handle drives air down a knee-shaped nozzle to holes near the bottom of the pail, under a disk on legs; at the same time two cords over a roller on the bellows rock a lever at its nose, which through a link and crank swings a paddle dasher back and forth beside the nozzle. An adjustable hole on the bellows' top sets how much air goes in; closed, the dasher churns alone. The patent gives no sizes; every size here is ours.
Zaawansowany
About 3 days

Instrukcje

1

Air for the cream

Wczytywanie notatnika Jupyter…
2

A bellows blowing air through the cream, years before

The tempered-air churn uses the bellows alone. Anderson's bellows also rocks a dasher by cords and a lever.
3

Read US 32,553

"The vessel being filled with cream, an up and down or vibratory movement is given to the upper portion of the bellows by means of the handle and a current of air thereby forced through the nozzle of the bellows into the cream through the apertures of the lower end of the nozzle. At the same time a vibrating motion is imparted to the dasher."
4

Box C, platform S, bars B and bellows A

Make a hardwood box C 520 x 360 mm and 450 high from 20 mm boards, and screw a platform S 380 x 340 x 30 mm to the ground at one end of it. Screw two hardwood bars B 40 x 20 mm across its top, 280 mm apart. Lay a hand bellows about 460 mm long on them, its nozzle toward the platform, and screw its bottom board to the bars. Bore a 30 mm hole in its top board as the aperture b and screw over it a hardwood slide in guides, to open it wide, part way or shut. Bore a 40 mm hole in the bottom board near its nose and glue a leather flap over it inside, hinged at one edge, as the valve that lets air in as the bellows opens. Screw two hardwood cross pieces D 200 x 30 mm on the top board and a hardwood handle E 400 mm long to them, reaching back.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego4 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna40 sztuk
MiechMiech1 sztuka
Skóra wyprawionaSkóra wyprawiona1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
5

Print the knee elbow

The elbow joining the nozzle's two tubes: two 22.4 mm sockets at right angles round a 17 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Nozzle G, disk I and the pail H

Cut a 22 mm stainless tube into a short end f 300 mm long and a long end 460 mm long and join them at right angles in the printed elbow with food-safe silicone, as the knee nozzle G; drill six 7 mm holes round the long end 25 mm above its foot. Fit the short end into the bellows' nozzle, sealed with leather. Cut an HDPE disk I 180 mm across, bore it 22.6 mm 80 mm from its centre for the tube, four 24 mm apertures h round its centre, and a socket boss at its centre; screw three hardwood legs g 60 mm long under it. Slide it on the tube so the tube's foot and the legs stand on the floor of a 20-litre food-grade pail H set on the platform. Cover the pail with butter muslin.

Materiały do tego kroku:

Rura ze stali nierdzewnejRura ze stali nierdzewnej1 sztuka
Filament PETGFilament PETG1 sztuka
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka
Skóra wyprawionaSkóra wyprawiona1 sztuka
Płyta HDPEPłyta HDPE1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Wkręty do drewnaWkręty do drewna3 sztuk
Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Gaza serowarskaGaza serowarska1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
WyrzynarkaWyrzynarka
KompasKompas
7

Staff J, dasher M, yoke, crank K and link L

Turn a hardwood staff J 20 mm across and 375 mm long, its foot to fit the disk's socket. Screw a hardwood paddle M 120 x 200 x 12 mm across it, its foot 25 mm above the disk. Fix a yoke of mild steel flat bar to the tube 340 mm above the pail's floor, with a ring round the staff's top. Pin a crank K of flat bar, 60 mm throw, on the staff's top, and join it with a flat bar link L to one end of the lever F.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Wkręty do drewnaWkręty do drewna4 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych2 sztuk
ZawleczkaZawleczka2 sztuk

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Pilarka stołowaPilarka stołowa
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
8

Print the forked bracket O

The forked bracket on the bellows' top board: 160 mm long, a 40 x 34 mm fork to slide on the post and a 30 x 24 slot for the roller P. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
9

Lever F, post N, bracket O, roller P and cords Q, R

Cut a hardwood lever F 300 x 30 x 15 mm and pivot it at its middle on an M10 bolt e upright in the bellows' nose block, with a wing nut. Screw a pedestal block to the box's back end and stand a hardwood post N 30 mm square, 380 tall, in it behind the bellows. Screw the bracket O to the top board's back end so its fork slides on the post, and pin a hardwood roller P 18 mm across in its slot. Tie a cord Q from the post's top, under the roller, to one end of the lever, and a cord R from the pedestal, over the roller, to the other end, both just taut with the bellows half open.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka
Nakrętka skrzydełkowaNakrętka skrzydełkowa1 sztuka
Podkładka płaskaPodkładka płaska2 sztuk
Filament PETGFilament PETG1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
SznurekSznurek1 sztuka
Wkręty do drewnaWkręty do drewna8 sztuk

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
10

The build in 3D

FreeCAD model of this build, the pail cut open: the box and platform, the bellows with its slide, cross pieces and handle, the knee nozzle down to the holed foot under the disk on its legs, the staff with its paddle and yoke, the lever on its bolt, the link, and the post with the forked bracket, roller and cords.
Plik projektowyBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the pail and cover it with the muslin. Work the handle up and down steadily, timing it: the bellows blows air out under the cream and the paddle rocks. Open or close the slide on the bellows' top to give more or less air. When the butter comes, unhook the link from the crank, draw the nozzle out of the bellows and lift the pail away; turn the disk on the tube until the staff's foot clears it and lift the dasher out. Take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka8 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
12

Troubleshooting

Bellows churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Charles T. Anderson** of Hyattstown, Montgomery County, Maryland, US 32,553, 18 June 1861, "Churn". He claimed the pivoted reciprocating dasher M with the bellows A and vertical nozzle G, and the nozzle G, detachable dasher M and eccentrically pivoted disk I together. His bellows was "of ordinary construction"; ours is a bought or made hand bellows with the patent's top aperture, valve and nozzle added. His vessel could be a firkin, pail, can or box. The patent gives no sizes; every size here is ours.

Materiały

21

Wymagane narzędzia

19

Pliki projektowe

3

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...