Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Hollow-Staff Plunger Churn: A Plunger in a Perforated Inner Cylinder Draws Air Down Its Staff on the Up Stroke
William Hamilton of St. Catharine, Missouri, received US 31,715, dated 19 March 1861, for a plunge churn with a perforated cylinder standing inside the tub. A bevelled plunger fits the cylinder like a piston on a hollow staff with a valve at its foot. Pulled up fast, it leaves a partial void below that the milk cannot fill quickly through the holes, so the valve opens and air rushes down the staff; pushed down, the valve shuts and the air is driven through the milk, which is thrown in and out through the holes against the tub's wall.
The patent gives no sizes; every size here is ours.
Początkujący
About 1 day
Instrukcje
1
1
Why air is drawn in on the up stroke
Why air is drawn in on the up stroke
Wczytywanie notatnika Jupyter…
2
2
A valve in a close-fitting dash, six weeks before
A valve in a close-fitting dash, six weeks before
Stevens's valve lets cream through his dash. Hamilton's lets air down a hollow staff, and his plunger works in a perforated cylinder.
3
3
Read US 31,715
Read US 31,715
"On the descent of the dasher said valve closes, and such admitted fresh air is forcibly made to permeate the body of milk and to abruptly counteract its tendency to fill the partial void below the dasher."
4
4
Tub A and inner cylinder B
Tub A and inner cylinder B
Use a 20-litre food-grade bucket as the tub A and cut a 12 mm HDPE lid to it with a 24 mm hole in the middle. Cut a strip of 1 mm stainless sheet 320 mm wide and 645 long, drill twelve rows of 6 mm holes along it 25 mm apart, 36 to a row, the rows staggered, and roll it into a cylinder B 200 mm across, riveting the lap.
Materiały do tego kroku:
Wiadro 20-litrowe1 sztuka
Płyta HDPE1 sztuka
Blacha ze stali nierdzewnej1 sztuka
Nity jednostronne8 sztukPotrzebne narzędzia:
Kompas
Wyrzynarka
Zestaw wierteł łopatkowych
Nożyce do blachy
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw nitownicy jednostronnej
Pilniki (pilnik ręczny)5
5
Print the feet (three)
Print the feet (three)
A foot that holds the cylinder 15 mm off the floor: 28 mm across, 25 high, with a slotted socket for the cylinder's edge. Print three. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Print the plunger C
Print the plunger C
The plunger: 196 mm across, bevelled on both faces from 120 mm at its hub to its 6 mm rim, with a hub 32 mm across and a 22.2 mm bore for the staff. PETG, 0.2 mm layers, 30 % infill, 4 walls.
7
7
Print the valve seat
Print the valve seat
The seat glued to the staff's foot under the plunger: 32 mm across, 6 thick, 19 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
8
8
Staff D, plunger C, valve b and handle
Staff D, plunger C, valve b and handle
Cut a 22 mm stainless tube with a 19 mm bore 600 mm long as the hollow staff D. Glue the plunger on it 25 mm above its foot with silicone and pin it, and glue the valve seat to its foot. Cut a 30 mm disc of 2 mm natural rubber sheet as the valve b and fix it under the seat by one edge with a small stainless pin, so it hangs open when pulled down and lies shut when pushed up. Turn a hardwood T handle 240 mm long and fit it on the staff's top, leaving the tube's mouth open.
Materiały do tego kroku:
Rura ze stali nierdzewnej1 sztuka
Filament PETG1 sztuka
Zawleczka1 sztuka
Płyta z kauczuku naturalnego1 sztuka
Pręt ze stali nierdzewnej1 sztuka
Deska z drewna liściastego1 sztuka
Klej do drewna1 sztuka
Kołki z twardego drewna1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Piła do metalu
Pilniki (pilnik ręczny)
Imadło warsztatowe
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Tokarka do drewna
Nożyce do blachy9
9
The build in 3D
The build in 3D
FreeCAD model of this build, cut open: the bucket, the perforated inner cylinder on its feet, the bevelled plunger on its hollow staff with the valve seat below, the lid and the T handle.
10
10
Churn and gather
Churn and gather
Stand the cylinder on its feet in the bucket and pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into it; it runs out through the holes to fill the bucket. Put the plunger in, the lid over the staff, and work it up and down briskly, timing it. When the butter comes, lift out the plunger and the cylinder, then give the cream a few gentle strokes with the plunger to gather the butter. Take it out, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka12 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej11
11
Troubleshooting
Troubleshooting
Plunger churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**William Hamilton** of St. Catharine, Linn County, Missouri, US 31,715, 19 March 1861, "Churn". He claimed, in a plunger churn with a hollow staff and air valve and the dasher's cylinder inside a tub with a milk space between, "a reticulated dasher cylinder or inner case so perforated as that a constant communication is established through the meshes of the inner cylinder between the inner and outer cylinders both above and below the dasher". He wrote that three to five minutes suffice and good cream makes butter in two; we have not tested that. He left the valve's form open ("any suitable valve"); ours is a rubber flap. The patent gives no sizes; every size here is ours.
Materiały
16- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 8 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
16- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
4Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Star Valve-Dash Churn: A Lever Drives a Close-Fitting Perforated Dash, Its Centre Valve Shuts Going Down and Opens Coming Up
autor: Buttercup
Obróbka drewna
4
0
0
0
0
0

Centrifugal-Dasher Churn: Curved Wings on a Hollow Shaft Throw the Cream at the Wall, a Fixed Disk Turns It Back
autor: Buttercup
Obróbka drewna
6
0
0
0
0
0

Atmospheric Barrel Churn: Reversed Concave Dashers Close to the Staves, Fresh or Warmed Air Piped to the Middle
autor: Buttercup
Obróbka drewna
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

