Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream
Buttercup

Autor

Buttercup

11. listopad 2026IE
4
0
0
0
0

Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream

Philip L. Clow of Cohoes, New York, received US 26,092, dated 15 November 1859, for a churn. One crank shaft and two pairs of bevel wheels turn two upright plate dashers in opposite directions at the same speed, so close that their paths cross. Their outer parts are hinged: turned one way they stand open to churn, turned the other they fold back to gather the butter. A pump on the same shaft blows air in at the bottom, and hot or cold water under the vessel's bottom keeps the cream at the right warmth. The patent gives no sizes; every size here is ours.
Zaawansowany
About 2 days, plus printing

Instrukcje

1

Two dashers whose paths cross, and the air the pump gives

Wczytywanie notatnika Jupyter…
2

A turning dasher with a hinged leaf for gathering, two months before

Hassler's leaf opens when the dasher is reversed. Clow hinges the outer halves of two counter-turning dashers so they fold back when reversed.
3

Read US 26,092

"I thus hinge the outer parts of the dashers to their central parts in order that after the butter has been produced from the milk or cream by turning the dashers in the directions pointed by the arrows x, x', the person who is churning may then, by simply turning the crank-shaft, I, and dashers, B, B', in the opposite direction, instantly lessen the extent of the space passed over or occupied by the dashers and thus increase the capacity of the churn or give room in the vessel, G, for the gathering of the butter into a mass"
4

Print the feet

A foot 30 mm across and 56 mm tall with a 10 mm recess in its top. Print three. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the eccentric t

A disc 90 mm across and 12 mm thick bored 12.6 mm 30 mm off its centre, for a 30 mm throw. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Vessel G on its reservoir F

Fit a brass spigot low in the side of a large pot at least 400 mm across, as the cock s. Stand the three printed feet in it and the stockpot on them, so water can lie under the stockpot's bottom and up its sides. Drill the stockpot's handle for the clamp hook m.

Materiały do tego kroku:

Duży garnekDuży garnek1 sztuka
Duży garnekDuży garnek1 sztuka
Kran mosiężnyKran mosiężny1 sztuka
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Klucz nastawnyKlucz nastawny
7

Cover n, posts, shafts and bevel wheels

Cut a hardwood cover 350 mm across, bored 13 mm at 55 mm either side of its middle for the dasher axes k, k', 10 mm for the thermometer and 12 mm for the air tube. Screw two posts 40 x 20 mm, 110 mm tall, on it 300 mm apart and bore them 12.8 mm 80 mm above the cover for the crank shaft I, 12 mm stainless, 442 mm long, with a crank and handle on one end. Fit the two bevel sets so the wheels on k and k' are driven from opposite sides by the pinions on I, back to back between them: the dashers then turn opposite ways at the same speed. Hold the axes in the cover with shaft collars.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna8 sztuk
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Zestaw przekładni stożkowej (stal, 1:1)Zestaw przekładni stożkowej (stal, 1:1)2 sztuk
Shaft CollarShaft Collar4 sztuk
HaftkaHaftka1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
KompasKompas
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Zestaw wkrętakówZestaw wkrętaków
Klucz nastawnyKlucz nastawny
Miara zwijanaMiara zwijana
8

Dashers B, B' with hinged leaves

From 2 mm stainless sheet cut two centre parts 50 x 220 mm and four leaves 65 x 220 mm. Fix a centre part to each axis k, k', 50 mm above the vessel's floor, and hang a leaf on each of its long edges with two small butt hinges, set so the leaves stop in line with the centre part one way and fold back the other. Set the two dashers a quarter turn apart.

Materiały do tego kroku:

Blacha ze stali nierdzewnejBlacha ze stali nierdzewnej1 sztuka
Zawias meblowy czopowyZawias meblowy czopowy8 sztuk
Śruby maszynoweŚruby maszynowe24 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową24 sztuk

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
Klucz nastawnyKlucz nastawny
9

Force-pump E and pipe u

Fix the eccentric on the crank shaft outside one post, and a 100 ml syringe upright beside it, its plunger joined to a strap round the eccentric. On its nozzle fit two check valves on a tee, one letting air in, the other out. Run silicone tube from the outlet to a stainless tube that passes down through the cover and along the vessel's side to 8 mm above its floor, its end turned inwards.

Materiały do tego kroku:

Strzykawka - LuerStrzykawka - Luer1 sztuka
Zawór zwrotnyZawór zwrotny2 sztuk
Wężyk silikonowyWężyk silikonowy1 sztuka
Rura ze stali nierdzewnejRura ze stali nierdzewnej1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Wkręty do drewnaWkręty do drewna4 sztuk

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
10

The build in 3D

FreeCAD model of this build, the vessel, reservoir and cover cut through: the stockpot on its feet in the water pot, the two dashers on their axes a quarter turn apart, the bevel wheels and crank shaft on their posts, the eccentric and syringe pump, the air tube and the thermometer. The dashers were turned through a full turn with their leaves open and folded.
Plik projektowyBLENDCC0 - Free
11

Churn, then gather

Fill the reservoir with warm or cold water until the cream will sit at about 15 °C. Pour about 12 litres of heavy cream into the stockpot, set the cover with the dashers in, hook it down, and put the thermometer through it. Turn the crank so the leaves stand open, timing it, while the pump bubbles air in at the bottom. When the butter comes, turn the crank the other way: the leaves fold back and the dashers gather the butter. Lift the cover and dashers out, gather the butter, empty the reservoir by the spigot, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka12 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
Czajnik elektrycznyCzajnik elektryczny
12

Troubleshooting

Contrary-dasher churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Philip L. Clow** of Cohoes, Albany County, New York, US 26,092, 15 November 1859, "Churn". He claimed the outer parts of the two contrarily revolving dashers hung to the central parts by hinges d, and the arrangement of the air-pump E and water-reservoir F with the revolving dashers and cream vessel. The patent gives no sizes; every size here is ours. His force-pump is not described inside: ours is a syringe with two check valves on an eccentric. His reservoir is a closed chamber under the vessel with a funnel, air-vent and cock; ours is an open pot of water with a spigot. His rubber packing between the pinions is left out.

Materiały

23

Wymagane narzędzia

17

Pliki projektowe

3

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...