Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Double Rotary Crag Churn: Two Shafts of Four-Edged Arms Turn Through Each Other in Twin Half-Cylinders
Aaron S. Cornell of New York received US 26,093, dated 15 November 1859, for what he called a "Double Rotary Crag Churn". Its bottom and cover are two half-cylinders side by side. One wheel and crank turn two shafts the same way; each carries crossed arms (crags), each arm two hollow half-cylinders back to back so it has four cutting edges, and the arms of one shaft pass between those of the other. A tap lets off the buttermilk into a draw with a sieve underneath.
The patent gives no sizes; every size here is ours.
Zaawansowany
About 3 days, plus printing
Instrukcje
1
1
Two cylinders back to back
Two cylinders back to back
Wczytywanie notatnika Jupyter…
2
2
Two dashers whose paths cross, the same day
Two dashers whose paths cross, the same day
Clow's two upright dashers turn opposite ways. Cornell lays his two shafts flat, turns them the same way and lets their arms pass between each other.
3
3
Read US 26,093
Read US 26,093
"As these pinions c, c, are both driven by the common wheel b, such pinions and their shafts will have rotary motion in the same direction so that as the arms on one shaft go down, those on the other shaft will pass upward, and the arms or dashers will thus be continually passing each other, giving the most complete and perfect agitation to the milk in the churn."
4
4
Print the crags i
Print the crags i
A set of two arms on a hub 40 mm across and 26 mm long, bored 16.6 mm: each arm two half-pipes back to back, tapering from 26 to 16 mm, reaching 105 mm from the shaft. Print eleven, with supports. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the driving wheel b
Print the driving wheel b
Spur wheel, 64 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the pinions c
Print the pinions c
Spur pinion, 16 teeth, module 3, 15 mm face, with a hub bored 16.6 mm and a cross hole for a pin. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Ends, trough and cover A
Ends, trough and cover A
Draw two circles 280 mm across, centres 200 mm apart, on 20 mm hardwood and cut two ends to that outline. Rout a rebate on the inside of each to the 243 mm circles for the sheet, bore 16.6 mm at the two centres, and saw each end across through the centres: the lower halves carry the trough, the upper halves the cover. Bend 1.5 mm stainless sheet, 400 mm long and 615 mm round, to the two lower arcs, and screw it into the lower rebates with silicone sealant. Make the cover A the same way on the upper halves, with two short stainless air pipes a. Fit a spigot J at the bottom of one end, where the two arcs meet.
Materiały do tego kroku:
Deska z drewna liściastego2 sztuk
Blacha ze stali nierdzewnej2 sztuk
Wkręty do drewna40 sztuk
Rura ze stali nierdzewnej1 sztuka
Kran mosiężny1 sztukaPotrzebne narzędzia:
Kompas
Wyrzynarka
Frezarka górnowrzecionowa
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wierteł łopatkowych
Nożyce do blachy
Pilniki (pilnik ręczny)
Ścisk stolarski listwowy
Zestaw wkrętaków8
8
Stand f and draw H
Stand f and draw H
Screw four legs 30 x 20 mm, 270 mm long, to the ends, a cross board shaped to cradle the trough, and two rails underneath. Make the draw H a hardwood tray 360 x 300 x 70 mm that slides on the rails, with a sieve l of stainless mesh on a frame inside it.
Materiały do tego kroku:
Deska z drewna liściastego2 sztuk
Klej do drewna1 sztuka
Wkręty do drewna24 sztuk
Siatka ze stali nierdzewnej klasy spożywczej1 sztukaPotrzebne narzędzia:
Pilarka stołowa
Wyrzynarka
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Nożyce do blachy
Ścisk stolarski listwowy9
9
Shafts K, crags and gearing
Shafts K, crags and gearing
Cut two 16 mm stainless shafts 495 mm long. Thread six crags on one and five on the other, 70 mm apart, so the five sit midway between the six, and turn each set a quarter turn from the last; pin them. Lay the shafts in the ends' half-holes, hold them with shaft collars, and put the cover on. Pin a pinion on each shaft's geared end, 25 mm outside the end. Bolt a bracket to the end, fix a 20 mm stud in it 66 mm above the shafts, and fit the wheel b on it meshing with both pinions, with a crank and handle.
Materiały do tego kroku:
Pręt ze stali nierdzewnej3 sztuk
Shaft Collar4 sztuk
Zawleczka15 sztuk
Podkładka płaska4 sztuk
Zestaw śrub sześciokątnych4 sztuk
Nakrętka samohamowna z wkładką nylonową4 sztuk
Deska z drewna liściastego1 sztuka
Kołki z twardego drewna1 sztuka
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Piła do metalu
Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Klucz nastawny10
10
The build in 3D
The build in 3D
FreeCAD model of this build, cut through the middle: the twin half-cylinder trough and cover with the air pipes, the two shafts with their crags passing between each other, the wheel and pinions, the tap, and the draw with its sieve on the stand. The shafts were turned through 12 positions.
11
11
Churn, then strain
Churn, then strain
Pour about 12 litres of heavy cream at about 15 °C into the trough, checked with the thermometer, and put the cover on. Turn the crank steadily, timing it. When the butter comes, draw off the buttermilk by the tap into the draw; shake the sieve to gather the bits of butter and put them back. Take the butter out, wash it in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka12 l
Sól morska gruboziarnista1 sztuka
Woda1 sztukaPotrzebne narzędzia:
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej12
12
Troubleshooting
Troubleshooting
Crag churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Aaron S. Cornell** of New York, US 26,093, 15 November 1859, "Rotary Churn". He claimed "the arrangement of the rotating shafts armed with the concave or recessed crags or dashers within the two concave or half cylinder chambers placed back to back". His crags were galvanized iron or metal; ours are printed. His pinions screw on with left-hand threads so that turning the wheel backwards takes them off; ours are pinned. The patent gives no sizes; every size here is ours.
Materiały
19- 2 sztukZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 64 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 3 sztukZastępnik
- 4 sztukZastępnik
- 15 sztukZastępnik
- 4 sztukZastępnik
- 4 sztukZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
18- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
4Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream
autor: Buttercup
JEDZENIE I NAPOJE
4
0
0
0
0
0

Brake-and-Ledge Bar Dasher Churn: Slotted Brakes Break the Current, Ledges Turn It Back to the Dasher
autor: Buttercup
Obróbka drewna
10
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

