Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Forged Flat Drills: Tool Steel Drawn to Blade and Square Taper Head, Tempered by Colour for the Metal to Be Drilled (Edwinson, 1886)
Forge

Autor

Forge

14. listopad 2026NO
7
0
0
0
0

Forged Flat Drills: Tool Steel Drawn to Blade and Square Taper Head, Tempered by Colour for the Metal to Be Drilled (Edwinson, 1886)

How a smith forged his own set of flat drills, from George Edwinson's series in Amateur Work (1886): 3/4 in. square tool steel drawn to a blade and shank with a square taper head, hardened in 45-50 F water and tempered by watching the colours run from a red-hot iron (pale straw for cast iron, orange yellow for wrought iron and copper, purplish yellow for wood), then ground to a notched gauge with clear corners.
Zaawansowany
An hour or two per drill

Instrukcje

1

His sizes

Wczytywanie notatnika Jupyter…
2

Read Edwinson

"A good drill may be made to turn out good work even when all other parts are indifferently made."
3

Draw the blade

Cut a two-foot length of 3/4 in. (19 mm) square tool steel. Heat 3 in. to blood red in a clean fire, never hotter, and hammer only down to a dull red before reheating. Draw out the blade and shank first (fig. 61), close to shape.

Materiały do tego kroku:

Pręt ze stali narzędziowejPręt ze stali narzędziowej1 sztuka

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
MłotekMłotek
Szczypce kowalskieSzczypce kowalskie
4

Forge the head

Cut off the length for the head, hold the blade and shank in grooved flat-bit tongs, and forge a square taper head to fit your brace socket, sides equal, shank and blade central. Finish at a dull red, set true, cool.

Potrzebne narzędzia:

Przecinak na gorącoPrzecinak na gorąco
Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
MłotekMłotek
Szczypce kowalskieSzczypce kowalskie
5

Shape and substance

Taper gradually from head to shank, keep the shank even for an inch or two, then let the blade swell out and thin toward the point (figs. 62, 63). Blade about 1/16 in. at the point and 1/8 in. at the corners for a 1/4 in. drill, up to 3/16 in. for 1/2 or 3/4 in.; a 1/4 in. drill's shank half as thick as a 1/2 in. blade. Leave blades a little full for grinding.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
MłotekMłotek
6

Harden

Heat to red and plunge the drill straight down into cool water of 45-50 F (7-10 C), holding it until cold: icy water makes the edges brittle. Brighten the blade and part of the shank on a brick or grit-stone.

Materiały do tego kroku:

WodaWoda1 sztuka

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
WiadroWiadro
TermometrTermometr
OsełkaOsełka
7

Temper by colour

Lay the shank across a red-hot piece of stout iron and watch the tints run toward the blade: straw, yellow, orange yellow, purplish yellow, purple, blues. For cast iron and hard brass stop when pale straw reaches the blade, dipping the blade to hold the later colours back while the shank cools in air. For wrought iron, soft steel or copper let the blade reach orange yellow. For wood only, let blade and shank reach purplish yellow and cool slowly.

Materiały do tego kroku:

WodaWoda1 sztuka

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Płyta żelaznaPłyta żelazna
WiadroWiadro
8

Grind to a gauge

Cut gauges from thin sheet brass with notches at the point angles (figs. 65, 66): very obtuse for cast iron and hard brass, more acute for wrought iron, tough steel and copper. Grind both edges equal with the point on the centre line, and give the corners clearance (fig. 70). Grind each blade to its finished size.

Materiały do tego kroku:

Blacha mosiężnaBlacha mosiężna1 sztuka

Potrzebne narzędzia:

Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
ToczydłoToczydło
9

Troubleshooting

Drill troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" IV, **Amateur Work, Illustrated**, vol. V (1886), pp. 348-351 and figs. 54-70 (checked on the archive.org scan amateurworkillus05lond; the scan reads 3/4 in. bar where the OCR text says 1/2). He also hardened glass and china drills in mercury: left out here (mercury is a poison). Metric figures, the brass gauge stock and the thermometer are ours.

Materiały

3

Wymagane narzędzia

11

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...