Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Cord-Lever Churn: A Cord Wound Round a Hollow Staff Turns It Back and Forth as a Hinged Lever Swings, a Loose Gatherer Rides Its Ribs
Buttercup

Autor

Buttercup

12. listopad 2026IE
10
0
0
0
0

Cord-Lever Churn: A Cord Wound Round a Hollow Staff Turns It Back and Forth as a Hinged Lever Swings, a Loose Gatherer Rides Its Ribs

H. Hagans of Brandonville, Virginia, received US 32,868, dated 23 July 1861, for a churn turned like a bow drill. The dasher staff stands in an ordinary churn inside a frame; a cord tied to a bar hinged on one post is wound three times round the staff and hooked into a hand lever hinged on the other side of the same post, the two held apart by folding braces. Swinging the lever slides the cord and turns the staff back and forth. The staff is hollow, so air enters above the lid and leaves near the bottom; wings stir the cream, and a gatherer, loose on two ribs, rides up and down with the butter and gathers it. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days

Instrukcje

1

Cord and staff, like a bow drill

Wczytywanie notatnika Jupyter…
2

A cord kept tight round a turning part, a year and a half before

Willson keeps a cord tight with a sprung bow. Hagans winds it three times round the staff and keeps it taut with folding braces between a lever and a bar.
3

Read US 32,868

"The cord H is attached to the counter-bar J and is wound three times around the staff E, and the other end is placed in the notch v of the lever I, with the knot outside."
4

Frame: bed A, uprights C, C', cap D

Glue up a hardwood bed A 760 x 320 x 30 mm and screw four hardwood steady pins n 12 mm round it where the churn's foot will stand. Mortise two hardwood uprights C and C' 50 x 50 mm, 560 tall, into the bed's ends, 710 mm apart over their centres. Cut a hardwood cap D 780 x 50 x 30 mm, bored 13 mm at the churn's centre for the staff's pivot. Pivot one end on the top of C' with a bolt a' and wing nut; at the other end cut a mortise h 12 x 20 mm over a bolt a in the top of C, with a flat bar binding plate i under its wing nut, so turning the plate lets that end lift off and swing aside.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego3 sztuk
Klej do drewnaKlej do drewna1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych2 sztuk
Nakrętka skrzydełkowaNakrętka skrzydełkowa2 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
Frezarka górnowrzecionowaFrezarka górnowrzecionowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Klucz nastawnyKlucz nastawny
Miara zwijanaMiara zwijana
5

Print the step b

The step in the churn's bottom: 40 mm across, 12 high, with a 22.6 mm socket 10 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the gatherer G

The butter-gatherer: a hub 60 mm across and 40 high, 23 mm bore with two slots for the ribs, and two tapered arms reaching 110 mm. Print it in two halves split through the slots, and screw them together on the staff. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Churn B, staff E, wings F, ribs c and gatherer G

Use a 20-litre food-grade bucket as the churn B, with the step in its bottom, and cut an HDPE lid with a 24 mm hole. Cut a 22 mm stainless tube 525 mm long as the hollow staff E; drill four 8 mm holes e round it 30 mm above its foot and one d 430 mm up, above the lid. Glue and screw four hardwood wings F 110 x 40 x 6 mm radially on it 60 to 100 mm up, and two hardwood ribs c 8 x 6 mm, 120 long, on opposite sides 170 to 290 mm up. Screw the gatherer's halves together round it between the ribs, so it slides freely up and down. Plug the tube's top and turn a 12 mm pivot on it for the cap.

Materiały do tego kroku:

Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Płyta HDPEPłyta HDPE1 sztuka
Rura ze stali nierdzewnejRura ze stali nierdzewnej1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna12 sztuk
Filament PETGFilament PETG1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
KompasKompas
WyrzynarkaWyrzynarka
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
8

Lever I, bar J, braces K and cord H

Cut a hardwood lever I 40 x 25 mm, 700 long with a handle, and a counter-bar J 520 long. Hang each on a butt hinge on opposite sides of C', 440 mm up, so they swing level, I on the front and J on the back, reaching past the staff on either side. Cut a notch v in I where it passes the staff. Make the braces K two strips of mild steel flat bar 200 mm long, each bolted to a lever at k 150 mm from the post, and bolted to each other at l, so they fold. Tie a braided cord H to J beside the staff, wind it three times round the staff above the lid, and hook its other end into the notch v with the knot outside, the braces straight and the cord taut.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Zawias meblowy czopowyZawias meblowy czopowy2 sztuk
Wkręty do drewnaWkręty do drewna12 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych3 sztuk
SznurekSznurek1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
Klucz nastawnyKlucz nastawny
9

The build in 3D

FreeCAD model of this build, the churn cut open: the bed with its steady pins, the two uprights and cap, the hollow staff with its wings, ribs and the loose gatherer, the step, the lid, the lever and counter-bar hinged on one post with the folding braces, and the cord wound round the staff.
Plik projektowyBLENDCC0 - Free
10

Churn

Swing the cap aside, set the churn between the steady pins with the staff in its step, pour in about 10 litres of heavy cream at about 15 °C, checked with the thermometer, put on the lid and swing the cap back over the staff's pivot, turning the binding plate. Wind on the cord. Swing the lever to and fro, timing it; the staff turns back and forth and draws air down through itself. When the butter comes, slow down so the gatherer collects it. Fold the braces, unhook the cord, swing the cap aside, lift out the staff, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka10 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
11

Troubleshooting

Cord-lever churn troubleshooting.

Flow

Loading...
12

History and honest limits

**H. Hagans** of Brandonville, Preston County, Virginia (now West Virginia), US 32,868, 23 July 1861, "Improved Churn"; the drawing spells the name Hagan. He claimed the self-adjusting rotary butter-gatherer G and ribs c with the dasher rod and wings, and the jointed braces K, hinged levers I and J and driving cord H with the dasher rod and post C'. His churn was an ordinary barrel; ours is a bucket. His staff was wood bored hollow; ours is a stainless tube. The patent gives no sizes; every size here is ours.

Materiały

16

Wymagane narzędzia

20

Pliki projektowe

3

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...