Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Atmospheric Combination Churn: A Fan Sends Air Down a Hollow Shaft and Out Through the Turning Arm
Buttercup

Autor

Buttercup

10. listopad 2026IE
7
0
0
0
0

Atmospheric Combination Churn: A Fan Sends Air Down a Hollow Shaft and Out Through the Turning Arm

William Smith Hall of Quincy, Massachusetts, received US 24,934, dated 2 August 1859, for what he called the "Atmospheric Combination-Churn". A crank on the cover turns a hollow upright shaft three times as fast through a large wheel and a pinion. A fan on the shaft's top takes in air, which goes down the shaft and out through a hollow arm at the bottom, while solid paddles on the shaft swing the cream past a rack of fixed bars. This rung builds it in a 20-litre bucket with printed parts. Hall gives no sizes but the 3:1 wheel; every other size is ours.
Średniozaawansowany
About 2 days, plus printing

Instrukcje

1

When does air come out of the hollow arm?

Wczytywanie notatnika Jupyter…
2

Air through the cream, before it

That churn pushed air down a hollow staff by hand. Hall's turns, and a fan feeds the air.
3

Read US 24,934

"By a rapid rotary motion of the hollow shaft from right to left, which is produced by the driving wheel being three times the size of the pinion, the air is forced into the fan down through the hollow shaft, while the curve of the hollow arm or paddle at the bottom of the shaft being in an opposite direction from the arms of the fan, a vacuum is created, which allows the air to be discharged, causing a vertical action on the milk or cream".
4

Print the hollow arm b

Two hollow half-discs (48 mm radius, 24 mm deep) on a hub that takes the 16 mm tube, their straight faces open on opposite sides as Fig. 7 draws, with the point c under the hub. Print it hub down with tree supports and pull them out through the open faces. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the cup d

The 60 mm cup with a cone recess for the point, a trap for an M6 nut underneath and a groove for an O-ring about 30 mm across on a 2 mm cord. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the paddles e

One solid paddle: a split hub for the 16 mm tube with an M5 clamp bolt, and a blade 24 mm tall reaching 96 mm. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Print the pinion g

The 12-tooth spur pinion (module 2) with a hub, bored for the 16 mm tube and cross-drilled for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
8

Print the driving wheel c

The 36-tooth crown wheel (module 2, three times the pinion) with its hub, bored for the 12 mm crank shaft and cross-drilled for a pin. Print it teeth up. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
9

Print the fan's upper disc

The plain 160 mm disc (Fig. 3) with the six curved arms standing on it (Fig. 4). Print it disc down. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
10

Print the fan's lower disc

The 160 mm disc with the centre hole (Fig. 4, a) on a split hub that clamps to the tube's top with an M5 bolt, Hall's "screw". PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
11

Cup d in the bucket's floor

Drill a 6.5 mm hole in the middle of the bucket's floor. Push an M6 nut into the cup's trap and lay the O-ring in its groove. Stand the cup over the hole and bolt it from underneath with a stainless M6 x 16 bolt and a washer, just tight enough to squeeze the O-ring. Fill the bucket with water to check it does not leak, then empty it.

Materiały do tego kroku:

Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna1 sztuka
Podkładka płaskaPodkładka płaska1 sztuka
O-ringO-ring1 sztuka

Potrzebne narzędzia:

Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
WodaWoda
12

Hollow shaft a, arm b and paddles e

Cut the stainless tube 507 mm long and deburr both ends. Press it 26 mm into the hollow arm's hub and check you can blow through the tube and out of both open faces. Clamp the four paddles on the tube with their middles 80, 140, 200 and 260 mm above the bucket's floor, each turned 45 degrees from the one below, with stainless M5 bolts and lock nuts. Stand the arm's point in the cup.

Materiały do tego kroku:

Rura ze stali nierdzewnejRura ze stali nierdzewnej1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych4 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową4 sztuk
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Klucz nastawnyKlucz nastawny
Miara zwijanaMiara zwijana
13

Rack of bars i on uprights j

Cut two hardwood uprights 30 x 20 mm, 366 mm long, and four bars 200 x 20 x 12 mm. Glue and screw the bars between the uprights' faces at 110, 170, 230 and 290 mm up, so the rack is 260 mm wide. Lower it into the bucket beside the shaft, the bars' middle line 25 mm from the shaft, and turn the shaft by hand: every paddle must pass between two bars.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna8 sztuk

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Papier ściernyPapier ścierny
Miara zwijanaMiara zwijana
14

Cover, journal f, chair and crank

Cut a 320 mm disc of 12 mm plywood and saw it in half. Notch the front half 24 mm across and the back half 50 mm across at the middle of the cut, as Fig. 6 draws, and bore a 24 mm air opening in the back half 90 mm from the middle. On the front half screw a hardwood block 80 x 56 x 30 mm over the notch, bored 17 mm for the tube, and two bearing blocks 44 x 30 mm, 110 mm tall, their near faces 45 and 115 mm from the middle, bored 12.6 mm through 90 mm up. Slide a 190 mm stainless rod through them for the crank shaft, pin the driving wheel on its inner end and a hardwood crank arm with a dowel handle 88 mm out on the other.

Materiały do tego kroku:

Płyta sklejkowaPłyta sklejkowa1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna6 sztuk

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
Piła ręcznaPiła ręczna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Miara zwijanaMiara zwijana
15

Pinion g and fan h

Lay both cover halves on the bucket, the tube through the journal. Pin the pinion on the tube so its teeth mesh fully with the driving wheel, just above the journal. Glue the fan's two discs together, arms between, and clamp the fan on the tube's top. Turn the crank: the shaft turns three times for each turn, and you feel air drawn in at the fan's rim.

Materiały do tego kroku:

Klej do drewnaKlej do drewna1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową1 sztuka

Potrzebne narzędzia:

Klucz nastawnyKlucz nastawny
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
16

The build in 3D

FreeCAD model of this build, cut open: the bucket, the cup and the hollow arm on the floor, the hollow shaft with four paddles passing between the rack of bars, the two-piece cover with its journal, chair and air opening, the driving wheel on the crank shaft turning the pinion, and the fan on top. The shaft was checked at 16 angles.
Plik projektowyBLENDCC0 - Free
17

Churn

Pour about 10 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the cover on. Turn the crank steadily, faster than the notebook's lowest speed, and time it. Lift the back half now and then to look. When the butter comes, lift the shaft and rack out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka10 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
18

Troubleshooting

Atmospheric churn troubleshooting.

Flow

Loading...
19

History and honest limits

**William Smith Hall** of Quincy, Massachusetts, US 24,934, 2 August 1859, "Churn". He claimed forcing a current of air through the milk or cream by the rotary fan combined with the upright hollow shaft, the rotary hollow and solid paddles and the stationary bars. He gives no sizes but the driving wheel three times the pinion, so every size here is ours: a crown wheel and pinion stand in for his wheel and pinion, and the fan, arm, paddles and rack are printed or cut to fit a 20-litre bucket. Our notebook is a rough upper-bound estimate, not a test.

Materiały

17

Wymagane narzędzia

16

Pliki projektowe

8

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...