Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Star Valve-Dash Churn: A Lever Drives a Close-Fitting Perforated Dash, Its Centre Valve Shuts Going Down and Opens Coming Up
Buttercup

Autor

Buttercup

11. listopad 2026IE
4
0
0
0
0

Star Valve-Dash Churn: A Lever Drives a Close-Fitting Perforated Dash, Its Centre Valve Shuts Going Down and Opens Coming Up

J. V. Stevens of Pomeroy, Ohio, received US 31,338, dated 5 February 1861, for "J. V. Stevens's Star Churn". A perforated dash fits the straight-sided body closely and is worked up and down by a lever on an arm at the rim. A loose perforated valve under the dash shuts its large centre opening on the down stroke, forcing the cream up through the holes, and drops open on the up stroke so the cream runs back down through the middle. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days

Instrukcje

1

How hard the cream is driven through the holes

Wczytywanie notatnika Jupyter…
2

A lever working the upright dash, eight months before

Cooper drives the old dasher by levers on a post. Stevens's lever works a dash that fits the body with a valve in it.
3

Read US 31,338

"... provided with a valve as at G which closes the aperture L, Fig. 2, upon the downward pressure of the lever C, Fig. 1, which causes the cream to be forced up through the perforations m in the dash and valve and upon the upward motion of the lever C the cream passes freely down through the aperture L and is again forced up through the perforations m, &c., which creates a violent agitation of the cream."
4

Body A, hoop and arm B

Use a straight-walled stainless stockpot about 280 mm across inside and 300 deep as the body A: the patent asks for one "of a uniform size inside from top to bottom". Bend a 3 mm stainless strip 25 mm wide into a hoop that clamps round the pot 20 to 45 mm below its rim, closed with a bolt and lock nut. Bolt to it an arm B of the same strip rising 290 mm beside the pot and bent out 35 mm to the pivot, 165 mm from the pot's centre, bored 8.4 mm for the pin I.

Materiały do tego kroku:

Duży garnekDuży garnek1 sztuka
Taśma ze stali nierdzewnej walcowana na zimno (420)Taśma ze stali nierdzewnej walcowana na zimno (420)1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych3 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową3 sztuk
Podkładka płaskaPodkładka płaska3 sztuk

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
Miara zwijanaMiara zwijana
5

Dash F with aperture L and bows E

Cut a 6 mm HDPE dash F 278 mm across, 1 mm smaller than the pot inside, with a 120 mm aperture L at its centre. Bore 18 mm holes m in two rings, 14 on a 176 mm circle and 20 on a 236 mm circle. Bend four strips of stainless strip 20 mm wide into bows E rising 76 mm, screw their feet to the dash just outside the aperture, and screw their tops to a hardwood collar 48 mm across glued on the stem 70 mm above the dash.

Materiały do tego kroku:

Płyta HDPEPłyta HDPE1 sztuka
Taśma ze stali nierdzewnej walcowana na zimno (420)Taśma ze stali nierdzewnej walcowana na zimno (420)1 sztuka
Wkręty do drewnaWkręty do drewna12 sztuk
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

KompasKompas
WyrzynarkaWyrzynarka
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Zestaw wkrętakówZestaw wkrętaków
6

Print the valve G

The valve G: a disk 150 mm across and 6 thick with eight 12 mm holes, and its sleeve P, 40 mm across and 16 high, with a 30 mm bore that slides easily on the stem. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Stem D, valve G and pin h

Cut a 28 mm hardwood dowel 480 mm long as the stem D and flatten its top 55 mm to a tongue 12 mm thick, bored 8.4 mm across 25 mm from the top for the pin j. Slide on the dash's collar, then from below the valve G, sleeve upward, and drive a 6 mm stainless pin h through the stem 40 mm under the dash, so the valve can drop about 30 mm open and rise to shut the aperture.

Materiały do tego kroku:

Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Filament PETGFilament PETG1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
8

Lever C and pins I and j

Cut a hardwood lever C 40 x 30 mm and 615 mm long, rounded at one end. Bore it 8.4 mm across 20 mm from that end for the pin I. Chisel a mortise 13 mm wide and 42 long through it, 150 to 192 mm from the pin hole, for the stem's tongue, and a slot 8.4 mm wide, 160 to 184 mm, through its sides for the pin j. Pin the lever to the arm B with an 8 mm stainless pin I and split pins, the tongue up through the mortise, and the 8 mm pin j through the slot and tongue.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
ZawleczkaZawleczka4 sztuk
Podkładka płaskaPodkładka płaska2 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
9

The build in 3D

FreeCAD model of this build, the pot cut open: the hoop and arm, the lever on its pin, the stem with its tongue and pin, the dash with its holes, aperture and bows, and the valve hanging open on its pin.
Plik projektowyBLENDCC0 - Free
10

Churn

Pour about 13 litres of heavy cream at about 15 °C, checked with the thermometer, into the pot, lower the dash in, and pin the lever. Work the lever down and up through its full stroke, briskly, timing it. When the butter comes, unpin the lever, lift the dash out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka13 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
11

Troubleshooting

Valve-dash churn troubleshooting.

Flow

Loading...
12

History and honest limits

**J. V. Stevens** of Pomeroy, Meigs County, Ohio, US 31,338, 5 February 1861, "Churn", which he called "J. V. Stevens's Star Churn". He claimed "the perforated valve dash to be worked with or without a lever", and wrote that it produced butter "under favorable circumstances in one and a half minutes by the clock"; we have not tested that. He preferred stoneware for the body, with a recess at the top for the hoop; ours is a stainless stockpot with a clamped hoop. His text says the body is of a uniform size inside, though Fig. 1 draws it tapering; we follow the text, which the close-fitting dash needs. The patent gives no sizes; every size here is ours.

Materiały

16

Wymagane narzędzia

18

Pliki projektowe

2

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...