Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Rotating-Receiver Stationary-Break Churn: The Whole Cream Vessel Turns, a Narrow Fixed Break Churns It
Buttercup

Autor

Buttercup

11. listopad 2026IE
6
0
0
0
0

Rotating-Receiver Stationary-Break Churn: The Whole Cream Vessel Turns, a Narrow Fixed Break Churns It

Mortimer S. Harsha of Sycamore, Illinois, received US 26,459, dated 13 December 1859, for what he called the "Vertical Rotating and Stationary Break Churn". Instead of a dasher, the whole cream vessel turns on an upright shaft with a pointed foot, driven by a gear and crank below it, while one narrow perforated break, fixed to a removable top, stands still near the vessel's side. The turning cream keeps going like a balance wheel, so little effort keeps it churning. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About a day, plus printing

Instrukcje

1

The turning cream against a still break

Wczytywanie notatnika Jupyter…
2

Fixed brakes in turning cream, three months before

Taylor turned a dasher among fixed brakes. Harsha turns the vessel itself against a single fixed break.
3

Read US 26,459

"This is accomplished by said break presenting only a small resisting surface to the moving cream, while the cream being made to rapidly rotate on said vertical or upright shaft only against said break dash, becomes, along with its receiver, a receptacle of the power applied, similar to that of a balance wheel, and so by its own accumulative force, when power is once applied, puts it in motion"
4

Print the gear wheel G

Crown wheel, 36 teeth on its face, module 2, with a hub bored 12.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the pinion

Spur pinion, 12 teeth, module 2, with a long hub bored 16.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the socket

A cup 50 mm across and 22 mm tall with a cone recess for the shaft's point. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Print the flange

A disc 200 mm across and 15 mm thick bored 16.6 mm, to carry the receiver. Print with 100 % infill. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
8

Base E, brace H, posts F and top D

Make a hardwood base 600 x 600 mm and screw the socket in its middle. Screw a brace H to it, an upright 30 x 40 mm with an arm reaching over the socket, bored 16.6 mm 25 to 55 mm up as the shaft's journal box. Tenon two posts 30 x 50 mm, 515 mm tall, into the base 490 mm apart, and make a top board 550 x 160 x 20 mm with mortises to drop onto their tenons so it lifts off. Set two chairs 44 x 30 mm, 124 mm tall, for the gear wheel's shaft.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego3 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna20 sztuk
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Dłuto do gniazdDłuto do gniazd
Pobijak drewnianyPobijak drewniany
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Miara zwijanaMiara zwijana
9

Shaft C, receiver A and gearing

File one end of a 16 mm stainless shaft 170 mm long to a point. Pin the pinion and the flange on it, stand its point in the socket through the journal box, and bolt the stockpot's bottom to the flange with stainless screws sealed with silicone. Fit the crown wheel on a 12 mm stainless shaft through the chairs, meshing under the pinion, with a crank and handle on its end.

Materiały do tego kroku:

Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Duży garnekDuży garnek1 sztuka
Śruby maszynoweŚruby maszynowe4 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową4 sztuk
Podkładka płaskaPodkładka płaska8 sztuk
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
Zestaw wkrętakówZestaw wkrętaków
10

Break dash B

Cut a hardwood break 60 x 15 mm long enough to reach from the top board to 25 mm above the receiver's floor, bore ten 16 mm holes through it, and fix it by a tenon through the top board so it hangs 30 mm in from the receiver's side.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Dłuto do gniazdDłuto do gniazd
Pobijak drewnianyPobijak drewniany
Papier ściernyPapier ścierny
11

The build in 3D

FreeCAD model of this build, the receiver cut through the middle: the base with its socket, brace and posts, the shaft with pinion and flange, the crown wheel and crank, the turning receiver and the fixed perforated break hanging from the top.
Plik projektowyBLENDCC0 - Free
12

Churn

Lift the top off, pour about 9 litres of heavy cream at about 15 °C into the receiver, checked with the thermometer, and put the top back. Turn the crank steadily, timing it: once the cream is moving it keeps going with little effort. When the butter comes, lift the top and break out, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka9 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
13

Troubleshooting

Rotating-receiver churn troubleshooting.

Flow

Loading...
14

History and honest limits

**Mortimer S. Harsha** of Sycamore, DeKalb County, Illinois, assignor to himself, Rufus S. Sanborn and H. B. Jones, US 26,459, 13 December 1859, "Churn". He claimed: "An entirely stationary break dash in combination with a cream receiver, made to rotate on a vertical or upright shaft". His break is made "of such size as the relative size of the machine requires, and of any common form or shape"; the patent gives no sizes, and every size here is ours. His receiver was tin, zinc or wood; ours is a stainless stockpot.

Materiały

14

Wymagane narzędzia

19

Pliki projektowe

5
  • harsha-rotating-receiver-stationary-break-churn-wheel-g.stlSTLCC0
  • harsha-rotating-receiver-stationary-break-churn-pinion.stlSTLCC0
  • harsha-rotating-receiver-stationary-break-churn-socket.stlSTLCC0
  • harsha-rotating-receiver-stationary-break-churn-flange.stlSTLCC0
  • harsha-rotating-receiver-stationary-break-churn.blendBLENDCC0

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...