Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Floating-Breaker Churn: A Propeller Dasher Under a Breaker That Floats in Wall Grooves, a Water Tube Held by the Faucet
Edward Lynch of Buffalo, New York, received US 27,864, dated 10 April 1860, for a churn. Propeller blades at the bottom of an upright crank-driven shaft drive the cream up against a breaker that floats on it: a ring round the shaft with bevelled arms whose ends ride loosely in grooves in the churn's sides, so it keeps its place at the surface for any amount of cream. A flat tube of warm or cold water stands inside, held by the faucet that also draws off the buttermilk.
The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing
Instrukcje
1
1
A breaker that floats
A breaker that floats
Wczytywanie notatnika Jupyter…
2
2
Paddles under a fixed partition, three weeks before
Paddles under a fixed partition, three weeks before
Sangster's partition is fixed below the cream. Lynch's breaker floats on top of it.
3
3
Read US 27,864
Read US 27,864
"They fit loosely in the grooves, so as to allow the breaker to float, upon the milk or cream, and hence always retain the same relation to the milk or cream, whether there be a large or small quantity in the churn."
4
4
Print the dash blades J
Print the dash blades J
Two-blade propeller 190 mm across, blades 80 x 50 x 5 mm pitched 30 degrees, on a hub bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the water tube L
Print the water tube L
Flat open-topped tank 160 x 30 mm and 210 deep, 3 mm walls, curved to stand against the bucket's side, with a collar under its foot to hold the faucet's nut. PETG, 0.2 mm layers, 100 % infill; fill it with water and check it holds before use.
6
6
Print the crown wheel
Print the crown wheel
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Print the pinion
Print the pinion
Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
8
8
Grooves i, breaks K and the faucet M
Grooves i, breaks K and the faucet M
Screw three pairs of hardwood strips 20 x 22 mm, 335 long, upright inside the bucket a third of a turn apart, 24 mm apart in each pair, as the grooves i. Screw two triangular hardwood breaks K, 30 mm deep and 150 tall, to the side near the floor between them, and seal every screw hole outside with silicone. Bore the bucket 22 mm, 30 mm above the floor and opposite the third groove, for the spigot. Set the tank against the side there, pass the spigot through the side and screw it into its nut, set in the tank's collar, so it holds the tank and opens into the churn.
Materiały do tego kroku:
Wiadro 20-litrowe1 sztuka
Deska z drewna liściastego1 sztuka
Wkręty do drewna16 sztuk
Kurek PVC1 sztuka
Filament PETG1 sztukaPotrzebne narzędzia:
Drukarka 3D z filamentem (FDM)
Pilarka stołowa
Zestaw otwornic
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wkrętaków
Klucz nastawny
Miara zwijana9
9
Floating breaker H
Floating breaker H
Cut a hardwood ring 100 mm across with a 60 mm hole and 50 deep. Cut three hardwood arms 20 mm thick and 50 deep, bevelled so the lower edge is 4 mm thick, the bevel facing the opposite way to the propeller's blades, long enough to reach loosely into the grooves; glue and screw them into the ring a third of a turn apart.
Materiały do tego kroku:
Deska z drewna liściastego1 sztuka
Klej do drewna1 sztuka
Wkręty do drewna6 sztukPotrzebne narzędzia:
Pilarka stołowa
Zestaw otwornic
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Papier ścierny
Ścisk stolarski listwowy
Zestaw wkrętaków10
10
Shaft B, cover P and gearing
Shaft B, cover P and gearing
Screw a hardwood step 50 x 50 x 6 mm to the floor's centre, bored 17 mm, 5 deep. Cut a 16 mm stainless shaft 465 mm long and turn or file its top 77 mm down to 12 mm; fit the propeller 8 mm above the floor. Cut a cover P of HDPE sheet to lie on the rim, bored 20 mm in the centre. Cut a hardwood cross piece N 350 x 205 x 25 mm with two hardwood fingers O 30 x 30 x 20 mm under it to rest on the cover, bored 13 mm for the shaft; fit the pinion above it, two chairs with a 12 mm crank shaft and the crown wheel, and a hardwood crank D with a dowel handle.
Materiały do tego kroku:
Klocek z drewna twardego1 sztuka
Pręt ze stali nierdzewnej2 sztuk
Płyta HDPE1 sztuka
Deska z drewna liściastego2 sztuk
Kołki z twardego drewna1 sztuka
Klej do drewna1 sztuka
Wkręty do drewna10 sztuk
Shaft Collar2 sztuk
Zawleczka1 sztukaPotrzebne narzędzia:
Piła do metalu
Pilniki (pilnik ręczny)
Imadło warsztatowe
Wyrzynarka
Pilarka stołowa
Wiertarko-wkrętarka akumulatorowa
Zestaw wierteł
Zestaw wierteł łopatkowych
Zestaw wkrętaków11
11
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: the propeller blades J on the shaft, the floating breaker H in its three grooves, the breaks K, the water tube L held by the faucet M, the cover P, the cross piece N with its fingers O, and the crank and gearing.
12
12
Churn
Churn
Pour about 6 litres of heavy cream into the bucket and set the breaker in its grooves; it floats on the cream. Pour warm or cold water from the kettle or tap into the tube L to bring the cream to about 15 °C, checked with the thermometer. Put on the cover, cross piece and gearing, and turn the crank steadily, timing it. When the butter comes, draw the buttermilk off at the faucet into a bowl, lift out the gearing, cover, breaker and butter, wash the butter in cold water until it runs clear, salt and weigh it.
Materiały do tego kroku:
Śmietanka kremówka6 l
Woda1 sztuka
Sól morska gruboziarnista1 sztukaPotrzebne narzędzia:
Czajnik elektryczny
Termometr z sondą pozostawianą w potrawie
Stoper
Cyfrowa waga kuchenna
Duża misa ze stali nierdzewnej13
13
Troubleshooting
Troubleshooting
Floating-breaker churn troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**Edward Lynch** of Buffalo, New York, US 27,864, 10 April 1860, "Churn", assigned to himself and Jas. J. McCool. He claimed the floating breaker with its ring, bevelled arms and grooves, and the tube held by the faucet. His tube is metal; ours is printed, and our faucet draws the milk through a collar under the tube's foot, our reading of his double-duty faucet. Every size here is ours.
Materiały
16- 1 sztukaZastępnik
- 2 sztukZastępnik
- 32 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
20- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- 1 vendor sell this, none ship to you yetZastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Pliki projektowe
5Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim
autor: Buttercup
Obróbka drewna
12
0
0
0
0
0

Hot-Water Cylinder Churn: Cream Is Crushed Between a Warm Turning Cylinder and an Adjustable Plate, Then Falls to a Dasher
autor: Buttercup
Obróbka drewna
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
autor: TheChef
RZEMIOSŁO
63
0
0
0
0
0
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

