Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub
Buttercup

Autor

Buttercup

11. listopad 2026IE
4
0
0
0
0

Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub

Jehu Mitchell of Aleppo township, Pennsylvania, received US 27,927, dated 17 April 1860, for a churn. The dasher hangs from above in a long journal box on a standard fixed to the lid, with no step or metal bearing in the tub, whose "oxidation ... imparts a bad flavor to the butter". One half of the box is a cap hinged at one side: lift out half the lid, unhook the cap and the dasher comes out with the gearing left in place. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing

Instrukcje

1

Held from above

Wczytywanie notatnika Jupyter…
2

A crank-turned upright dasher, one week before

Lynch's shaft stands in a step on the bottom. Mitchell hangs his from above, with nothing in the tub.
3

Read US 27,927

"Suspending the dasher within an elongated hinged journal box in the manner described, combined the following advantages. A rigid bearing is afforded to the dasher so as to prevent any tremulous motion, without the necessity of any metallic step or bearing within the churn, the oxidation of which imparts a bad flavor to the butter."
4

Print the driving wheel E

Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the pinion M

Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Lid B and C, brakes O

Cut a hardwood lid 15 mm thick to sit on the bucket's rim and saw it in two across the middle: part C carries the standard, part B lifts out. Cut a 28 mm half-hole in the middle of the cut edge for the shaft and a 30 mm hole in B to look in. Screw three hardwood brakes O, 30 mm deep and 245 tall, to the bucket's side a third of a turn apart, and seal the screw holes outside with silicone.

Materiały do tego kroku:

Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Wkręty do drewnaWkręty do drewna6 sztuk
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
Pilarka stołowaPilarka stołowa
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
7

Standard D, journal box and cap G

Glue up a hardwood standard 60 mm wide and 66 deep, 111 mm tall above the lid, with its back 22 mm rising to 217 mm and bored 12.6 mm across near the top for the wheel's axle. Mortise it into lid part C behind the shaft's hole. Cut a cap G 60 x 30 mm, 111 tall, and bore a 25.2 mm hole down the joint between standard and cap, half in each. Hang the cap on a butt hinge at one side and fit a hook H and eye I on the other.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Zawias meblowy czopowyZawias meblowy czopowy1 sztuka
HaftkaHaftka1 sztuka
Wkręty do drewnaWkręty do drewna4 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
Ścisk stolarski listwowyŚcisk stolarski listwowy
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Zestaw wkrętakówZestaw wkrętaków
8

Dasher J with wings N and collars K and L

Cut a 25 mm hardwood dowel 485 mm long and glue a 12 mm stainless spindle into its top, standing 56 mm out. Glue two hardwood wings 200 x 60 x 20 mm across it, 20 and 140 mm above its foot, each bored with two 24 mm holes. Fit a hardwood collar L 44 mm across just below the lid, and a collar K 40 mm across on the spindle resting on the box's top. Set the shaft in the box, close the cap, and key the pinion M on the spindle above K.

Materiały do tego kroku:

Kołki z twardego drewnaKołki z twardego drewna2 sztuk
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Klocek z drewna twardegoKlocek z drewna twardego1 sztuka
Shaft CollarShaft Collar1 sztuka
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Pilarka stołowaPilarka stołowa
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Papier ściernyPapier ścierny
9

Driving wheel E and crank

Pass a 12 mm stainless axle through the standard's back, fit the wheel E on it meshing the pinion, and a hardwood crank with a dowel handle on the other end; hold it with a collar and split pin.

Materiały do tego kroku:

Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Shaft CollarShaft Collar1 sztuka
ZawleczkaZawleczka1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Imadło warsztatoweImadło warsztatowe
10

The build in 3D

FreeCAD model of this build, the bucket cut open: the dasher J with its two wings hanging from the journal box, the brakes O, the lid, the standard D with its hinged cap G, hook and eye, and the wheel E with pinion M.
Plik projektowyBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the lid and dasher in place, and turn the crank steadily, timing it. To look at the butter, lift out lid part B. When the butter comes, lift part B out, unhook the cap and take the dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka8 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
12

Troubleshooting

Hung-dasher churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Jehu Mitchell** of Aleppo township, Greene County, Pennsylvania, US 27,927, 17 April 1860, "Churn". He did not claim a churn without a bottom step nor a hinged bearing alone, but the gearing, standard, hinged cap, dasher and collar together. His journal box runs higher; ours stops below the crown wheel. His wings and brakes are "of common construction"; our two wings and three brakes, and every size, are ours.

Materiały

16

Wymagane narzędzia

18

Pliki projektowe

3

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...