Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Crank-and-Link Double-Dasher Churn: Two Dashers' Cranks Joined by a Curved Link, One Lever Turns or Rocks Both
Buttercup

Autor

Buttercup

12. listopad 2026IE
8
0
0
0
0

Crank-and-Link Double-Dasher Churn: Two Dashers' Cranks Joined by a Curved Link, One Lever Turns or Rocks Both

Robert Parker of North Cohocton, New York, received US 33,213, dated 3 September 1861, for working two upright wing dashers in an oval churn with one lever. A cap that hooks onto ears on the box carries a horizontal crank over each dasher, coupled to its shaft. A curved link joins the two crank pins and the lever is pivoted to its middle: moving the lever's end round turns both dashers together, pushing it straight to and fro rocks them, and the user can work it from the front or the side. Unhook the cap and the whole mechanism lifts off. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days

Instrukcje

1

Turning or rocking with one lever

Wczytywanie notatnika Jupyter…
2

A mechanism that lifts off the churn as one, four months before

Stilwell swings his driving arm back on a frame. Parker's whole drive is in a cap that hooks onto ears and lifts off.
3

Read US 33,213

"The object of my invention is to so arrange the mechanism that by a rectilinear movement of the operator either a vibratory or rotary motion may be given to the dashers."
4

Oval box A, cover, cups and ears C

Make an oval box A whose inside is two 90 mm half rounds 140 mm apart joined by straight sides, 300 deep: a hardwood floor and two straight hardwood sides, with 1.5 mm stainless sheet bent round the ends in grooves, all sealed with silicone. Seal a printed cup for each dasher's foot on the floor at the half rounds' centres. Cut an HDPE cover to the outside with a 27 mm hole over each cup. Screw a hardwood ear C 30 x 60 mm, 140 long, to each end, standing above the box, with a mortise c 24 mm wide and 20 deep near its top.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego3 sztuk
Blacha ze stali nierdzewnejBlacha ze stali nierdzewnej1 sztuka
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna24 sztuk
Filament PETGFilament PETG1 sztuka
Płyta HDPEPłyta HDPE1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
KompasKompas
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
5

Print the cups (two)

A cup for a dasher's foot: 44 mm across, 14 high, a 26 mm socket 10 deep. Print two. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Wing dashers B and shafts a

Turn two hardwood dasher shafts 25 mm across, 320 long, and set a 16 mm stainless rod 80 mm long 20 mm into each top, with a flat filed on its end as the tenon of the coupling f. Mortise four hardwood wings 120 x 120 x 12 mm through each, two crossed at 35 to 155 mm up and two crossed at 160 to 280, turned 45 degrees from the lower pair.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Klej do drewnaKlej do drewna1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
7

Cap D, cranks e, link o and lever h

Glue up a hardwood cap D 400 x 120 x 60 mm, cut a recess d 260 x 100 mm, 42 deep, in its underside, and a slot through its front wall for the lever. Glue a tenon b 24 x 20 mm on each end to drop into the ears' mortises, and fit a hook and eye at each end to hold it. Bore it 16.6 mm through over each dasher. Make each crank e of a 16 mm stainless shaft through the cap with a slot in its foot to take the dasher's tenon (the coupling f), and a mild steel flat bar arm, 35 mm throw, with an 8 mm pin. Bend a 6 mm steel rod into a half round joining the two pins, eyes at its ends, and fix a pivot eye at its middle. Pivot a hardwood lever h, 500 long with a handle, on the eye so it comes out through the cap's slot.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Klej do drewnaKlej do drewna1 sztuka
HaftkaHaftka2 sztuk
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych3 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową3 sztuk
ZawleczkaZawleczka2 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
Frezarka górnowrzecionowaFrezarka górnowrzecionowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Zestaw wkrętakówZestaw wkrętaków
8

The build in 3D

FreeCAD model of this build, half the box cut away: the oval box with its cups and ears, the two wing dashers, the cap hooked onto the ears with the two cranks, the curved link and the lever coming out of its slot.
Plik projektowyBLENDCC0 - Free
9

Churn

Stand the dashers in their cups, pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, put on the cover over the shafts, and lower the cap so the cranks' slots take the dashers' tenons and its tenons drop into the ears; hook it. Move the lever's end round in a small circle to turn the dashers, or push it straight to and fro to rock them, timing it. When the butter comes, unhook and lift off the cap, lift out the dashers, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka12 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
10

Troubleshooting

Crank-link churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Robert Parker** of North Cohocton, Steuben County, New York, US 33,213, 3 September 1861, "Improved Churn". He claimed "the combination of the cranks, the curved link, and the operating-lever". His box was oval and staved; ours has straight sides and stainless ends. He does not describe the dashers beyond "wing-dashers"; ours follow his Fig. 1. The patent gives no sizes; every size here is ours.

Materiały

18

Wymagane narzędzia

18

Pliki projektowe

2

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...