Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Spiral-Corrugated Water-Jacket Churn: A Bevelled Strip Dasher Throws Cream Against Diagonal Corrugations in a Warmed or Cooled Chamber
Buttercup

Autor

Buttercup

11. listopad 2026IE
10
0
0
0
0

Spiral-Corrugated Water-Jacket Churn: A Bevelled Strip Dasher Throws Cream Against Diagonal Corrugations in a Warmed or Cooled Chamber

David Sherman of Uniontown, Maryland, and Robert W. Fenwick of Washington, D.C., received US 29,445, dated 31 July 1860, for a churn whose chamber is a nearly round metal plate corrugated diagonally all over, set in a water-tight wooden case with room around it for warm or cold water. A cranked dasher of two bevelled end bars carries strips standing across the corrugations; it flings the cream against them, they break its current, and it runs back to the middle. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 3 days

Instrukcje

1

Spiral corrugations from four printed rings

Wczytywanie notatnika Jupyter…
2

Churning inside a water jacket, a year before

Gissinger stands two churns in a water box. Sherman and Fenwick wrap the water round one corrugated chamber.
3

Read US 29,445

"It is a very essential thing to force the cream against a surface which will break the direction of the current and at the same time allow the cream to flow back to the point from which is was moved, for by breaking the current, the churning is facilitated. Our diagonally or spirally corrugated churning chamber does this perfectly."
4

Print the chamber rings (four)

One ring of the chamber B: 100 mm long, a plain 208 mm cylinder outside, 28 spiral corrugations inside (crests 95 mm, troughs 101 mm from the axis), open over the top with two upright lips. Print four; they are identical and their corrugations run on from one to the next. Needs a 220 mm bed. PETG, 0.2 mm layers, 30 % infill, 4 walls, printed standing on an end.
Plik projektowySTLCC0 - Free
5

Case A and chamber B

Glue up two hardwood ends 30 x 290 x 288 mm. On each, 160 mm above the bottom edge, draw circles 203 and 209 mm across and rout a groove 6 mm deep between them, with two straight grooves 4 mm wide rising from it to the top edge, about 125 mm apart between centres, for the lips. Cut hardwood sides 20 x 288 x 400, a bottom and a top 20 x 250 x 400, and cut a mouth 122 mm wide the length of the top. Seal the four rings end to end with silicone, set their ends and lips in the grooves with silicone, and glue and screw the case together round them, sealing every joint inside: the space round the chamber is the water jacket. Bore a 16 mm hole in the top 100 mm off centre and seal in a short stainless tube a for the water. In one end bore 16 mm holes at the chamber's bottom and at the case's bottom and fit rubber stoppers: drains for the buttermilk and the water (ours). Make a hardwood lid for the mouth with a plug that fits it.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego4 sztuk
Filament PETGFilament PETG1 sztuka
Uszczelniacz silikonowyUszczelniacz silikonowy2 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna40 sztuk
Rura ze stali nierdzewnejRura ze stali nierdzewnej1 sztuka
Korki gumoweKorki gumowe2 sztuk

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Pilarka stołowaPilarka stołowa
KompasKompas
Frezarka górnowrzecionowaFrezarka górnowrzecionowa
WyrzynarkaWyrzynarka
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
Miara zwijanaMiara zwijana
6

Dasher: shaft D, bars b and strips c

Cut two hardwood end bars b 50 x 20 mm and 156 mm long, and bevel both ends of each across its width, from the full length on one edge to 100 mm on the other, the two bevels facing opposite ways. Cut six hardwood strips c 20 x 6 mm and 360 mm long, and screw three, one below another, along each pair of bevelled ends, so they stand on opposite sides of the shaft and run end to end across the corrugations. Bore the bars 16 mm at their middles, 360 mm apart over their outer faces, on a 16 mm stainless shaft D 515 mm long, and pin them. Pass the shaft through the ends at the chamber's centre, hold it with a shaft collar outside each end, and pin on a crank of mild steel flat bar, 120 mm throw, with a hardwood handle.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Wkręty do drewnaWkręty do drewna12 sztuk
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
ZawleczkaZawleczka2 sztuk
Shaft CollarShaft Collar2 sztuk
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Komplet dłut do drewnaKomplet dłut do drewna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Zestaw wkrętakówZestaw wkrętaków
7

The build in 3D

FreeCAD model of this build, its front half cut away: the four printed rings with their spiral corrugations, set in the grooved case ends with the water jacket round them, the top with its mouth, lid and water tube a, the drains, and the dasher with its bevelled bars and strips on the cranked shaft.
Plik projektowyBLENDCC0 - Free
8

Temper and churn

Pour about 5 litres of heavy cream into the chamber, so its surface stays below the shaft. Pour water through the tube a into the jacket, warm in a cold room or cold in a warm one but never hotter than the hand can bear, until the cream reads about 15 °C on the thermometer. Put on the lid and turn the crank steadily, timing it. When the butter comes, draw the buttermilk off by its stopper into a bowl, take out the butter through the mouth, wash it in cold water until it runs clear, salt and weigh it. Drain the jacket by its stopper.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka5 l
WodaWoda1 sztuka
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
9

Troubleshooting

Corrugated-chamber churn troubleshooting.

Flow

Loading...
10

History and honest limits

**David Sherman** of Uniontown, Maryland, and **Robert W. Fenwick** of Washington, D.C., US 29,445, 31 July 1860, "Churn", assigned to D. Sherman and Bernard Mills. They claimed "corrugating the surface of the near cylindrical churning chamber diagonally or spirally ... in combination with the blades c, c, (of the dasher) which are set so as to stand across the diagonal or spiral corrugations". Their chamber was a bent, corrugated metal plate; ours is printed rings with plain outsides. The drains are ours; the text does not say how the buttermilk or water is let off. The patent gives no sizes; every size here is ours.

Materiały

15

Wymagane narzędzia

19

Pliki projektowe

2
  • sherman-fenwick-spiral-corrugated-water-jacket-churn-ring.stlSTLCC0
  • sherman-fenwick-spiral-corrugated-water-jacket-churn.blendBLENDCC0

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...