Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Adjustable-Board Churn: A Perforated Board on a Pin Beside the Wall Is Set to Break the Cream or Gather the Butter
Buttercup

Autor

Buttercup

11. listopad 2026IE
6
0
0
0
0

Adjustable-Board Churn: A Perforated Board on a Pin Beside the Wall Is Set to Break the Cream or Gather the Butter

George H. Van Vleck of Buffalo, New York, received US 28,219, dated 8 May 1860, for a churn. Wings near the foot of an upright crank-driven staff swirl the cream; beside the wall stands a perforated board on its own pin, held at the angle wanted by pins in the bottom. Set one way it breaks the globules as the cream is forced against it; set the other it gathers the butter between it and the side. Its foot is cut away so the wings pass under it. The patent gives no sizes; every size here is ours.
Średniozaawansowany
About 2 days, plus printing

Instrukcje

1

Two settings of one board

Wczytywanie notatnika Jupyter…
2

An upright crank churn, three weeks before

Mitchell's breaks are fixed to the wall. Van Vleck's board turns on a pin and is set to the work.
3

Read US 28,219

"The board may be placed so as to set at any desired angle, either for gathering the butter between it and the sides of the churn, or for breaking the globules, when the cream is forced against it. As the board is changed so the openings or perforations are changed and their edges and sides are presented differently for assisting in breaking the globules which contain the butter of the cream."
4

Print the toothed wheel F

Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the pinion E

Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Board C, shaft d, socket and guide d'

Cut a hardwood board 15 mm thick, 95 wide and 297 tall. Leave its outer 15 mm full height and a foot 40 mm long and 17 high at the bottom; cut the rest away between 20 and 62 mm up so the wings pass under. Bore eight 14 mm holes x in two rows in its face, and glue a 10 mm stainless shaft d along its outer edge, standing 45 mm above it. Screw a hardwood socket block bored 10.6 mm, 8 deep, to the bucket's floor 122 mm from the centre, and a hardwood guide d' bored 10.6 mm inside the wall above it, 325 mm up.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Klocek z drewna twardegoKlocek z drewna twardego1 sztuka
Wkręty do drewnaWkręty do drewna4 sztuk
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Papier ściernyPapier ścierny
Zestaw wkrętakówZestaw wkrętaków
7

Pins a

Glue three 10 mm dowel pins 20 mm tall into the floor on a circle 35 mm round the socket, toward the centre and 50 degrees apart, so the board's foot drops between the middle pin and either outer one: 25 degrees one way to break, 25 degrees the other to gather.

Materiały do tego kroku:

Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

KątomierzKątomierz
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
8

Staff B, wings D, cross piece H and gearing

Screw a hardwood step 50 x 50 x 8 mm to the floor's centre, bored 12.6 mm, 6 deep. Cut a 25 mm hardwood staff 348 mm long, glue 12 mm stainless spindles into its ends, and fix a hardwood wing 170 x 30 x 15 mm across it 25 mm above the floor. Cut a hardwood cross piece H 350 x 205 x 25 mm to sit on the rim, bored 13 mm over the centre as the guide I; fit the pinion on the staff's top, two chairs with a 12 mm crank shaft and the wheel F, and a hardwood crank with a dowel handle.

Materiały do tego kroku:

Klocek z drewna twardegoKlocek z drewna twardego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna2 sztuk
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej2 sztuk
Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna10 sztuk
Shaft CollarShaft Collar2 sztuk
ZawleczkaZawleczka1 sztuka
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Pilarka stołowaPilarka stołowa
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Ścisk stolarski listwowyŚcisk stolarski listwowy
9

The build in 3D

FreeCAD model of this build, the bucket cut open: the staff with its wings, the perforated board on its shaft set at 25 degrees between two pins, the guide d', and the cross piece with the crank, wheel F and pinion E.
Plik projektowyBLENDCC0 - Free
10

Churn

Set the board leaning against the swirl, its face meeting the cream, to break. Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, put the cross piece and gearing on, and turn the crank steadily, timing it. When the butter comes, lift the board and drop it between the other pair of pins to gather, and turn slowly until the butter collects against the side. Lift off the gearing, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka8 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
11

Troubleshooting

Adjustable-board churn troubleshooting.

Flow

Loading...
12

History and honest limits

**George H. Van Vleck** of Buffalo, New York, US 28,219, 8 May 1860, "Churn". He claimed the box, the dasher and staff, and the adjustable hinged board with its pins and openings. He says the board can be set "at any desired angle"; our three pins give two settings, and which of them breaks best and which gathers best is for the maker to find and note. Every size here is ours, and our gears are printed.

Materiały

13

Wymagane narzędzia

17

Pliki projektowe

3

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...