Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Round-Bottom Square Churn: A Geared Dasher Turns in a Vessel Round Up to Its Blades and Square Above, Breakers From the Lid
Thomas R. Markillie of Winchester, Illinois, received US 33,154, dated 27 August 1861, for the shape of a churn vessel: round at the bottom as high as the dasher, square above. A geared crank on the lid turns a dasher with sloping blades near the bottom; the blades lift and swirl the cream in the round part, and it is thrown from side to side and corner to corner against two breakers hanging from the lid and a rib on the wall. He made the vessel of earthenware, as easiest to keep sweet.
The patent gives no sizes; every size here is ours.
Intermediário
About 3 days
Instruções
1
1
Round below, square above
Round below, square above
A carregar o notebook Jupyter…
2
2
A turning dasher against breakers on the wall, six months before
A turning dasher against breakers on the wall, six months before
Stirewatt lines a round body with notched ribs. Markillie shapes the vessel itself, round below and square above.
3
3
Read US 33,154
Read US 33,154
"The shape of the dasher-blades and their inclined position to the bottom when revolving is such as to give a lifting and revolving motion to the cream, while the shape of the cream-vessel further assists in lessening the time usually required to churn, for the cream when driven by the dasher against the breakers E and c and from side to side and corner to corner of the cream-vessel is very greatly agitated."
4
4
Print the corner fillets (four)
Print the corner fillets (four)
A corner fillet: fills one corner of the square vessel so the bottom 110 mm is a 260 mm round, with a flare above. Print four. PETG, 0.2 mm layers, 30 % infill, 4 walls.
5
5
Print the bottom skirt
Print the bottom skirt
The rounded edge ring for the floor: 260 mm across, 12 high, sloping inside. Needs a 270 mm bed, or print in quarters. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Print the step F
Print the step F
The step for the dasher's pin: 36 mm across, 10 high, with an 8.6 mm hole 7 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
7
7
Print the breaker c
Print the breaker c
The breaker on the wall: a curved rib 16 mm deep and 98 high, to stand on the round part's wall. PETG, 0.2 mm layers, 30 % infill, 4 walls.
8
8
Vessel A: square box with a round bottom, lugs a
Vessel A: square box with a round bottom, lugs a
Glue up a square hardwood box 260 x 260 mm inside and 300 deep from 20 mm boards with a 20 mm bottom. Seal the four corner fillets into the corners with food-safe silicone so the lower 110 mm is round, the skirt round the floor's edge, the step at the centre of the floor and the rib c on one side of the round part. Seal every joint. Screw a hardwood lug a 60 x 25 mm to two opposite sides near the top to lift it.
Materiais para este passo:
Tábua de madeira de lei4 peças
Cola de madeira1 peça
Filamento PETG1 peça
Parafusos para madeira24 peçasFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de mesa
Berbequim sem fios
Jogo de brocas
Sargento de barra
Conjunto de chaves de fendas
Fita métrica9
9
Print the dasher blades (four)
Print the dasher blades (four)
A dasher blade: 93 x 30 x 6 mm on a 28 mm hub with a 12.2 mm bore. Print four; set each at 30 degrees. PETG, 0.2 mm layers, 30 % infill, 4 walls.
10
10
Print the pinion D
Print the pinion D
The bevel pinion on the dasher shaft: 14 teeth, module 2.5, 12.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
11
11
Print the driving wheel C
Print the driving wheel C
The driving wheel: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
12
12
Dasher D, lid B with breakers E, wheel C and crank
Dasher D, lid B with breakers E, wheel C and crank
Cut a 12 mm stainless dasher shaft 360 mm long with a pin turned on its foot to fit the step. Fix the four blades on a printed or hardwood hub 25 to 45 mm above its foot, a quarter turn apart, each sloping 30 degrees. Cut a 12 mm HDPE lid B to the box's outside in two halves; hinge one half to the box and leave the other loose, with hooks and eyes b to fasten them. Screw two hardwood breakers E 12 x 80 mm, 140 long, under the lid 70 mm either side of the centre, reaching down to 160 mm above the floor. Bore the lid 14 mm at the centre for the shaft. Screw two hardwood bearing blocks 50 x 25 x 118 mm on the fixed half, bored 16.6 mm across 93 mm up; pin the pinion on the shaft 40 mm above the lid, and run a 16 mm stainless shaft 150 mm long through the blocks with the wheel C pinned on meshing it, a shaft collar, and a crank of mild steel flat bar, 100 mm throw, with a hardwood handle.
Materiais para este passo:
Varão de aço inoxidável2 peças
Filamento PETG1 peça
Chapa de PEAD1 peça
Dobradiça de livro para móvel2 peças
Colchete (macho e fêmea)2 peças
Tábua de madeira de lei1 peça
Parafusos para madeira12 peças
Shaft Collar1 peça
Contrapino3 peças
Barra chata de aço macio1 peça
Cavilhas de madeira dura1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra tico-tico
Conjunto de brocas de pá
Berbequim sem fios
Jogo de brocas
Serra de arco para metais
Limas (lima de mão)
Torno de bancada
Conjunto de chaves de fendas13
13
The build in 3D
The build in 3D
FreeCAD model of this build, half cut away: the square vessel with its four corner fillets making the bottom round, the skirt, step and wall rib, the dasher with four sloping blades, the two breakers from the lid, and the gearing and crank on the fixed half of the lid.
14
14
Churn
Churn
Set the dasher in its step, pour about 9 litres of heavy cream at about 15 °C, checked with the thermometer, into the vessel so it stands a little above the round part, close the loose half of the lid and hook it. Turn the crank steadily, timing it. When the butter comes, lift the loose half, take out the dasher by lifting the fixed half on its hinges, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater9 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável15
15
Troubleshooting
Troubleshooting
Round-bottom churn troubleshooting.
Flow
Loading...
16
16
History and honest limits
History and honest limits
**Thomas R. Markillie** of Winchester, Scott County, Illinois, US 33,154, 27 August 1861, "Improvement in Churns". He claimed "the cream-vessel constructed round at the bottom as high up as the height of the dashers, with the rest of the body of the vessel square, and this in combination with the revolving dasher". He made the vessel of earthenware, finding it the easiest to clean and keep sweet; ours keeps his shape in a sealed hardwood box with printed fillets, which must be scalded and dried with care; his vessel narrows toward the bottom, ours has straight sides. His gearing was a bevel wheel and pinion; ours is a printed crown wheel and pinion. The patent gives no sizes; every size here is ours.
Materiais
16- 4 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 2 peçasReferência
- 36 peçasReferência
- 2 peçasReferência
- 1 peçaReferência
- Referência
- 2 peçasReferência
- 1 peçaReferência
- 3 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
16- Referência
- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
8Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Notched-Rib Churn: A Solid S-Winged Dasher Turns Inside Upright Ribs Whose Notches Alternate, Crossing the Cream's Currents
por Buttercup
Marcenaria
7
0
0
0
0
0

Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow
por Buttercup
Marcenaria
8
0
0
0
0
0

Centrifugal-Dasher Churn: Curved Wings on a Hollow Shaft Throw the Cream at the Wall, a Fixed Disk Turns It Back
por Buttercup
Marcenaria
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

