Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow
Moses D. Wells of Morgantown, Virginia, received US 31,756, dated 19 March 1861, for a churn dasher shaped as a slanted open box: two flat end plates carrying the journals, two curved face pieces with lips at opposite corners, and two open sides. It turns on a horizontal axis in a box whose bottom is curved to its sweep. Turned fast it churns; turned the same way slowly, it gathers the butter inside itself, the lips keeping it from being thrown out, so it lifts out in a lump.
The patent gives no sizes; every size here is ours.
Intermediário
About 2 days
Instruções
1
1
Churning fast, gathering slow
Churning fast, gathering slow
A carregar o notebook Jupyter…
2
2
A round-bottomed box with a turning dasher, eight months before
A round-bottomed box with a turning dasher, eight months before
Park's box works the butter with pins. Wells's hollow dasher gathers it inside itself.
3
3
Read US 31,756
Read US 31,756
"The dasher being hollow, a few slow turns of the same causes the butter to collect within the box so as to be removed in a lump. ... The object of the diagonal lips b', b', is, to gather the butter against, and prevent it from being thrown out of the box in turning it around."
4
4
Body B with a curved bottom, legs and lid
Body B with a curved bottom, legs and lid
Glue up two hardwood ends 22 mm thick, 350 mm wide and 320 tall. On each draw the inside: a 300 mm half circle with its centre 160 mm up, and straight sides rising 150 mm above the centre to the top. Rout a groove 1.6 mm wide and 8 deep on that line. Cut a slot 16.6 mm wide down from the top edge to the centre, rounded at its foot, as the journal bearing, and a hardwood keeper that fills the slot above the journal. Bend a 1.5 mm stainless sheet 416 mm long into a U to fit the line, set it in both grooves with silicone sealant, and screw hardwood sides 22 mm thick outside its straight parts. Screw four hardwood legs 40 x 40 mm, 390 long, to the ends, splayed out. Cut a hardwood lid 444 x 350 x 22 mm, notched over the keepers, with a 25 mm air opening o.
Materiais para este passo:
Tábua de madeira de lei4 peças
Chapa de aço inoxidável1 peça
Cola de madeira1 peça
Parafusos para madeira30 peçasFerramentas necessárias:
Serra de mesa
Bússola
Serra tico-tico
Tupia
Conjunto de formões para madeira
Maço de borracha
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Sargento de barra
Conjunto de chaves de fendas
Fita métrica5
5
Print the end plates a (two)
Print the end plates a (two)
An end plate of the dasher: 15 mm thick, the slanted outline of Fig. 1 with curved top and bottom edges, a 50 mm boss at the centre. Print two; drill each 16 mm at the centre for a journal. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Dasher D: end plates a, face pieces b with lips b', journals
Dasher D: end plates a, face pieces b with lips b', journals
Cut two strips of 1.5 mm stainless sheet 360 mm long, each 160 mm wide; bend each to a curve of about 300 mm radius following the end plates' curved edges, with a 20 mm lip b' at one long edge turned on round the corner. Screw them to the end plates' curved edges, the lips at diagonally opposite corners, leaving the two slanted sides open. Push a 16 mm stainless journal into each end plate's boss and pin it: one 40 mm long, the other 90 mm for the crank. Lay the journals in the slots and drop in the keepers. Pin a crank of mild steel flat bar, 120 mm throw, with a hardwood handle, on the long journal.
Materiais para este passo:
Filamento PETG1 peça
Chapa de aço inoxidável1 peça
Parafusos para madeira16 peças
Varão de aço inoxidável1 peça
Contrapino3 peças
Barra chata de aço macio1 peça
Cavilhas de madeira dura1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Tesoura de chapa
Maço de borracha
Berbequim sem fios
Jogo de brocas
Serra de arco para metais
Limas (lima de mão)
Torno de bancada
Conjunto de chaves de fendas7
7
The build in 3D
The build in 3D
FreeCAD model of this build, cut open: the round stainless bottom in grooved ends with slotted bearings and keepers, the legs and lid with its air opening, and the slanted hollow dasher with its curved, lipped face pieces and crank.
8
8
Churn and gather
Churn and gather
Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, so it stands below the axis, and put on the lid. Turn the crank briskly, timing it. When the butter comes, turn the same way slowly for a few turns until it gathers inside the dasher. Lift off the lid and keepers, lift the dasher out by its journals, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater10 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável9
9
Troubleshooting
Troubleshooting
Box-dasher churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Moses D. Wells** of Morgantown, Monongalia County, Virginia (now West Virginia), US 31,756, 19 March 1861, "Churn-Dasher". He claimed "the oblique box dasher D constructed and operating substantially as set forth, that is to say, with two flat sides, two curved sides, and two open sides, and turned in the same direction for churning, and for gathering the butter, but at various velocities". He says only that the journals have "suitable connections to facilitate the removal of the dasher"; ours lie in open slots under keepers. The patent gives no sizes; every size here is ours.
Materiais
13- 4 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 46 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 3 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 10 lReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
21- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
2Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Pin-Cylinder Box Churn: A Cylinder of Square Pins Turns Through a Row of Pins in the Lid, Then Washes the Butter in the Churn
por Buttercup
Marcenaria
8
0
0
0
0
0

Spiral-Corrugated Water-Jacket Churn: A Bevelled Strip Dasher Throws Cream Against Diagonal Corrugations in a Warmed or Cooled Chamber
por Buttercup
Marcenaria
10
0
0
0
0
0

Sealed Screw-Axis Drum Churn: The Dasher's Axis Screws Into It Through a Pipe in the Side, a Sprung Washer Keeps It Tight
por Buttercup
Marcenaria
10
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

