Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Slotted-Gate Dash Churn: A Hand Wheel Turns a Crank Pin in the Slot of a Sliding Gate, Which Drives the Dash Up and Down
Buttercup

Criado por

Buttercup

11. novembro 2026IE
6
0
0
0
0

Slotted-Gate Dash Churn: A Hand Wheel Turns a Crank Pin in the Slot of a Sliding Gate, Which Drives the Dash Up and Down

Henry A. Nevers and Charles Ross of Claremont, New Hampshire, received US 30,686, dated 20 November 1860, for a compact plunge churn on its own stand. A hand wheel on a shaft turns a disk whose crank pin runs in a horizontal slot cut in a wooden gate; the gate slides up and down in grooves in two standards and carries the dash rod, so turning the wheel works the dash evenly up and down. Pull one pin and the dasher comes free. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

Pin in a slot against a connecting rod

A carregar o notebook Jupyter…
2

A wheel plunging the dash by a connecting rod, four months before

Paff drives his dash rod from a flywheel by a pitman. Nevers and Ross put the crank pin in a slot instead.
3

Read US 30,686

"Motion is communicated to the wheel G, and through the shaft F to the disk H, the pin c on which as it revolves plays in the slot d, in the gate I, by which means the gate is raised and lowered vertically and with it the rod J, and dash K, which agitates the cream as required."
4

Base A, standards C, C' and D, platform E

Glue up a hardwood base A 500 x 460 x 25 mm. Rout an 11 mm groove 11 deep down one face of two hardwood standards C, C' 40 x 40 x 830 mm and screw them upright on the base, grooves facing and their inner faces 320 mm apart, either side of where the churn stands. Screw a standard D 40 x 40 x 575 mm behind the churn, 220 mm from its centre. Screw a platform E 177 x 400 x 20 mm across from two cheek blocks on the backs of C, C' to the top of D, its top 575 mm above the base.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei3 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira30 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
TupiaTupia
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
5

Bearings a, shaft F, disk H, pin c and wheel G

Screw two hardwood bearing blocks a 30 x 50 x 70 mm on the platform, 85 and 170 mm behind the gate's plane, bored 16.6 mm across 45 mm up. Run a 16 mm stainless shaft F 217 mm long through them, held by a shaft collar. Cut a hardwood disk H 180 mm across and 18 thick, fix it on the shaft's front end 40 mm from the gate's plane, and drive a 10 mm stainless pin c 72 mm long through it 60 mm from the centre so 54 mm stands out toward the gate. Cut a hardwood wheel G 240 mm across and 20 thick, fix it on the shaft's back end, and set a hardwood handle b 100 mm from its centre.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável2 peças
Shaft CollarShaft Collar1 peça
ContrapinoContrapino2 peças
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira8 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
BússolaBússola
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Conjunto de chaves de fendasConjunto de chaves de fendas
6

Gate I with slot d and tongues e

Glue up a hardwood gate I 320 x 200 x 22 mm and cut a slot d 10.5 mm wide and 132 mm long across it, its middle 100 mm above the gate's foot. Glue hardwood strips 10 x 10 mm along both upright edges as the tongues e. Glue a hardwood block 50 x 50 x 60 mm under the gate's foot, bored 25.6 mm up 51 mm for the dash rod, and bore it 6 mm across for the pin f. Slide the gate down between the standards, its tongues in the grooves, the crank pin in the slot.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
TupiaTupia
Conjunto de formões para madeiraConjunto de formões para madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Sargento de barraSargento de barra
7

Body B, cover L, dash rod J and dash K

Use a 20-litre food-grade bucket as the body B, standing between the standards. Cut a 12 mm HDPE cover L to its top, 304 mm across, with a 27 mm hole in the middle, saw it in two halves through the hole and screw a hardwood knob g on each. Cut a 220 mm HDPE disk as the dash K and screw it to the foot of a 25 mm hardwood dash rod J 378 mm long. Put the dash in the bucket, the cover halves round the rod, push the rod up into the gate's block and pin it with a 6 mm stainless pin f.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Chapa de PEADChapa de PEAD1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Parafusos para madeiraParafusos para madeira6 peças

Ferramentas necessárias:

BússolaBússola
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Serra de arco para metaisSerra de arco para metais
Conjunto de chaves de fendasConjunto de chaves de fendas
8

The build in 3D

FreeCAD model of this build, the bucket cut open: the base, the grooved standards and the gate with its slot and tongues, the platform with its bearings, the shaft, disk and crank pin, the wheel and handle, the dash rod and dash.
Arquivo de designBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket before fitting the cover. Turn the wheel steadily by its handle, timing it. When the butter comes, lift off the cover halves, pull the pin f, lift out the dash, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater10 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
10

Troubleshooting

Slotted-gate churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry A. Nevers** and **Charles Ross** of Claremont, Sullivan County, New Hampshire, US 30,686, 20 November 1860, "Churn". They claimed "the combined arrangement of the driving shaft F, face plate and crank pin H, c, with the vertically reciprocating carriage I, provided with a horizontal slot d, and the rod J, of the dasher". Their wheel was spoked and their gate's top scalloped; ours are plain wooden discs and a plain gate, and our churn body is a bucket. The patent gives no sizes; every size here is ours.

Materiais

12

Ferramentas necessárias

17

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...