Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Screw-Piston Box Churn: The Case Turns and a Piston Runs End to End Along a Five-Start Screw
Buttercup

Autor

Buttercup

10. listopad 2026IE
8
0
0
0
0

Screw-Piston Box Churn: The Case Turns and a Piston Runs End to End Along a Five-Start Screw

E. L. Pratt of Philadelphia received US 25,306, dated 30 August 1859, for a square box churn with a piston inside. A screw of four or five threads runs the length of the case; the piston rides on it. With the screw held still, turning the case drives the piston from one end to the other, forcing the cream through small grooves across its edges and through holes that a turning disk opens or closes. To finish, the case is held and the screw turned, so the piston presses the butter into each end. Pratt gives no sizes; every size here is ours.
Zaawansowany
About 3 days, plus printing

Instrukcje

1

Cream through the grooves

Wczytywanie notatnika Jupyter…
2

Cream forced through small openings, two weeks before

Lehaye pumped the cream through slots he could narrow. Pratt drives a piston along a screw and narrows its holes with a disk.
3

Read US 25,306

"The operator now takes hold of the crank handle (h) and gives rotary motion to the case (A), thus causing the diaphragm or piston (C) to be forced, by the screw shaft (D), toward, and eventually against, one of the ends (e or e') of the said case (A), when he then gives an opposite rotary motion to the said case (A), and thus forces the said diaphragm (C) to the other end of the same".
4

Print the screw sections

One 100 mm section of the five-start screw, 50 mm across with a 50 mm lead, bored 12.4 mm for the rod. Print four, standing up. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the piston's outer plate m

A 196 mm square plate 10 mm thick with the five-start nut, eight 16 mm holes o and grooves p across its edges. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Print the piston's other outer plate m

The same plate with an arc slot for the disk's peg. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
7

Print the piston's middle plate m'

The middle plate with a 140.6 mm hole for the turning disk. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
8

Print the disk n

The 140 mm disk with eight holes set between the plates' holes and a peg that comes out through the slot. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Plik projektowySTLCC0 - Free
9

Case A: sides d, ends e and e', bolts f

From 20 mm hardwood cut four sides 412 mm long, two 200 mm and two 240 mm wide, and two end pieces 280 x 280 x 40 mm. Rout a groove 6 mm deep and 20.5 mm wide in each end's inner face to take the sides' edges as a square 200 mm inside. Cut a 180 x 120 mm opening in one 200 mm side for the lid. Bore the ends 11 mm at the four corners, 128 mm from the middle each way, and draw the case together with four M10 rods, washers and nuts. Bore a blind 20.6 mm hole 30 mm deep in the middle of one end for journal i, and a 20.6 mm hole through the other for journal k. Soak the case in water overnight so it swells tight.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego3 sztuk
Pręt gwintowanyPręt gwintowany4 sztuk
Nakrętka sześciokątnaNakrętka sześciokątna8 sztuk
Podkładka płaskaPodkładka płaska8 sztuk

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
Piła ręcznaPiła ręczna
DłutaDłuta
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Zestaw wiertełZestaw wierteł
Ścisk stolarski listwowyŚcisk stolarski listwowy
Kątownik stolarskiKątownik stolarski
Klucz nastawnyKlucz nastawny
WodaWoda
10

Screw shaft D and its journals

Thread the four screw sections on a 580 mm M12 stainless rod so their threads run on from one to the next, with a 20 mm stainless tube on each side as journals i and k. Clamp the stack with nuts and washers so the screw turns with the rod. Thread the piston on before the last section goes on. Put journal i in the blind hole, pass journal k through the other end, and draw the case up round them.

Materiały do tego kroku:

Pręt gwintowanyPręt gwintowany1 sztuka
Rura ze stali nierdzewnejRura ze stali nierdzewnej1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna4 sztuk
Podkładka płaskaPodkładka płaska4 sztuk
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Klucz nastawnyKlucz nastawny
11

Piston C

Glue the middle plate to the plain outer plate, drop the disk into its hole, peg up, and glue the slotted plate on top so the peg comes out through the slot and the disk turns freely. Line up the nuts' threads before the glue sets by running the piston onto a screw section.

Materiały do tego kroku:

Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Ścisk stolarski listwowyŚcisk stolarski listwowy
12

Lid q, frame B, cranks and pin v

Make the lid from hardwood to fit the opening, with a 6 mm lip all round, and two hardwood buttons r screwed to the case to turn over it. Fix a hardwood block on the outside of end e and pin a 20 mm steel stub in it as journal g, with a crank h. Fix a crank l on the rod's end outside journal k. Build a frame of two uprights on a base, 580 mm apart, with open slots for the journals. Bore 10 mm holes through each upright and its end piece, and through the crank l, for the pin v.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Drewno iglaste 70x70 mmDrewno iglaste 70x70 mm2 sztuk
Pręt stalowy surowyPręt stalowy surowy2 sztuk
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Wkręty do drewnaWkręty do drewna16 sztuk
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Miara zwijanaMiara zwijana
13

The build in 3D

FreeCAD model of this build, the case cut open: the sides let into the ends and held by the four corner bolts, the lid and its buttons, the five-start screw on its journals, the piston in the middle with its grooves and holes, the two cranks and the frame. The case was turned through 16 angles.
Plik projektowyBLENDCC0 - Free
14

Churn, then press

Turn the disk's peg to open or close the holes for the cream's thickness. Pour about 6 litres of heavy cream at about 15 °C, checked with the thermometer, through the lid opening, button the lid down and pin crank l to its upright. Turn crank h one way about seven and a half turns until the piston stops at one end, then back the other way, timing it. When the butter comes, pin the case instead and turn crank l to drive the piston against each end and press the butter there. Open the lid, lift the butter out, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka6 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
15

Troubleshooting

Screw-piston churn troubleshooting.

Flow

Loading...
16

History and honest limits

**E. L. Pratt** of Philadelphia, assignor to himself and R. B. Fitts, US 25,306, 30 August 1859, "Churn". He claimed the rotary case with a piston that both moves along and turns on a screw, with grooves across its edges, and the piston of three pieces with a disk to open, adjust or close its holes. He gives no sizes, so every size here is ours; he made the piston of wood, and ours is printed, with a peg through a slot to turn the disk.

Materiały

14

Wymagane narzędzia

19

Pliki projektowe

6

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...