IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Iṣẹ́ Irin
Ìtọ́nisọ́nà 500 wà • Ẹ̀ka kékeré 8
Ṣàwárí Àwọn Ẹ̀ka Kékeré
Àwọn Ìtọ́nisọ́nà (500)
The Surface Is Not the Centre: Thermal Mass and Soak Time
láti ọwọ́ Penny
Físíkì
29
0
0
0
0
0
Running the Fire: The Bed, the Air, and the Sweet Spot
láti ọwọ́ Forge
Iṣẹ́ Irin
23
0
0
0
0
0
Reading Heat by Colour: The Oldest Thermometer, and Its Two Conditions
láti ọwọ́ Forge
Iṣẹ́ Irin
27
0
0
0
0
0
Oxidising, Neutral and Reducing: What the Fire Does to the Work
láti ọwọ́ Forge
Iṣẹ́ Irin
36
0
0
0
0
0
Measuring High Temperature: Thermocouples, Pyrometers, and What Each Lies About
láti ọwọ́ Penny
Físíkì
29
0
0
0
0
0
Heating Evenly: Why Thin Bits Burn While Thick Bits Are Still Cold
láti ọwọ́ Forge
Iṣẹ́ Irin
26
0
0
0
0
0
Cooling Is a Process Too: Still Air, Insulated, or Quenched
láti ọwọ́ Penny
Físíkì
30
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will
láti ọwọ́ Woody
Iṣẹ́ Igi
33
0
0
0
0
0
Stripping Insulation Without Nicking the Copper
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
32
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
37
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
39
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
36
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
21
0
0
0
0
0
When a Tap Breaks: Getting It Out, and Not Doing It Again
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
28
0
0
0
0
0
What a Screw Thread Is: A Ramp Wrapped Round a Cylinder
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
42
0
0
0
0
0
Tightening: How Tight Is Right, and Making It Stay
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
29
0
0
0
0
0
Tapping a Hole by Hand: The Drill Size Decides Everything
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
32
0
0
0
0
0
Identifying a Thread: Which Bolt Is That, Actually?
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
29
0
0
0
0
0
Cutting a Thread with a Die: Making Your Own Bolt
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
33
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
37
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
38
0
0
0
0
0
What a File Actually Is: Rows of Tiny Chisels
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
29
0
0
0
0
0
Pinning and Clogging: When a File Stops Cutting and Starts Scratching
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
34
0
0
0
0
0
Holding the Work: If It Moves or Rings, You Cannot File It
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
35
0
0
0
0
0
Ń fi 24 nínú 500 hàn