IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Àwọn Ìtọ́nisọ́nàÌMỌ̀-Ẹ̀RỌ
ÌMỌ̀-Ẹ̀RỌ
Ìtọ́nisọ́nà 1,101 wà • Ẹ̀ka kékeré 8
Ṣàwárí Àwọn Ẹ̀ka Kékeré
Àwọn Ìtọ́nisọ́nà (1,101)
Reading a Worn Tooth: What the Damage Is Telling You
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
48
0
0
0
0
0
Mounting and Alignment: Runout, Misalignment and the Contact Pattern
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
46
0
0
0
0
0
Choosing a Gear Type: Spur, Helical, Bevel, Worm or Rack
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
55
0
0
0
0
0
Gear Trains: Idlers, Compounding and Hitting a Given Ratio
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
44
0
0
0
0
0
Centre Distance and Backlash: The Gap That Has to Be There
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
45
0
0
0
0
0
The Involute: Why Gear Teeth Are That Shape and No Other
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
56
0
0
0
0
0
Tooth Count and Ratio: One Extra Tooth Changes Everything
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
43
0
0
0
0
0
Module and Pitch: The One Number Two Gears Must Share
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
50
0
0
0
0
0
Designing For the Process: A Printable Part Is a Different Shape
láti ọwọ́ 3DBonanza
Ìṣelọ́pọ̀ Àfikún
31
0
0
0
0
0
Reading a Failed Print: The Fault Names Itself If You Look
láti ọwọ́ 3DBonanza
Ìṣelọ́pọ̀ Àfikún
32
0
0
0
0
0
Walls and Infill: Strength Comes From the Outside, Not the Middle
láti ọwọ́ 3DBonanza
Ìṣelọ́pọ̀ Àfikún
39
0
0
0
0
0
Warping: Why Big Flat Parts Lift at the Corners
láti ọwọ́ 3DBonanza
Ìṣelọ́pọ̀ Àfikún
33
0
0
0
0
0
Tolerance and Clearance: Printed Holes Come Out Small, Every Time
láti ọwọ́ 3DBonanza
Ìṣelọ́pọ̀ Àfikún
38
0
0
0
0
0
Overhangs, Bridges and Support: What the Machine Can Print Over Thin Air
láti ọwọ́ 3DBonanza
Ìṣelọ́pọ̀ Àfikún
35
0
0
0
0
0
Orientation: A Printed Part Is Weakest Between Its Layers
láti ọwọ́ 3DBonanza
Ìṣelọ́pọ̀ Àfikún
36
0
0
0
0
0
The First Layer Decides Everything Above It
láti ọwọ́ 3DBonanza
Ìṣelọ́pọ̀ Àfikún
44
0
0
0
0
0
The Fuse Protects the Wire, Not the Thing You Plugged In
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
37
0
0
0
0
0
The Crimp: A Good One Is a Cold Weld, Not a Squeeze
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
48
0
0
0
0
0
Testing What You Wired: Continuity, Polarity, Then Power
láti ọwọ́ Ed
Ẹ̀rọ Ìtanná
22
0
0
0
0
0
Stripping Insulation Without Nicking the Copper
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
39
0
0
0
0
0
Strain Relief and Routing: Wires Fail Where They Are Held
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
28
0
0
0
0
0
Soldering a Wire Joint: Not the Same Job as Soldering a Board
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
31
0
0
0
0
0
Choosing the Wire: Solid or Stranded, and What the Gauge Number Means
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
26
0
0
0
0
0
Choosing a Connector: What Has to Come Apart, and What Must Not
láti ọwọ́ Volt
Ẹ̀rọ Ìtanná
32
0
0
0
0
0
Ń fi 24 nínú 1101 hàn