Ubufatanye
UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
IbishushanyoUMUCO N'AMATEKA
UMUCO N'AMATEKA
Ibishushanyo 2.500 birahari • Ibyiciro bito 3
Reba Ibyiciro Bito
Ibishushanyo (2.500)
Cam-Arm Tubing Cutter: Two Swinging Arms Keep the Wheel and Rollers Evenly Round Any Tube (Lutsker, 1959)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Sprung-Leg Tubing Cutter: a Bent Rod With a Disk Outside and a Roller Inside, the Handle's Screw Bends One Leg In (Zeiler, 1958)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Slip-Knob Tube Cutter: the Feed Knob Turns the Screw Through Spring-Loaded Plates and Slips Before the Tube Is Crushed (Parker, 1944)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
V-Slide Tubing Cutter: Two Slide Halves Held on the Ways by One Spring Clip, a Reamer on the Frame (Thewes, 1938)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Four-Edge Chatterless Countersinks: Two Pairs of Edges Set Off the Centre Lines, One Raked Each Way (Manewich, 1946)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Adjustable-Knife Countersink: Three Knives Set Out Evenly by a Collar and Stopped by a Depth Pin (Logan, 1921)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Spiral-Edge Countersinks: One Curved Slot Up the Cone Makes an Edge That Slices Instead of Scraping (Laursen, 1926)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Clamp-On Countersink: Two Blocks Screwed Round Any Drill, Twin Cutters Countersink the Hole as It Is Bored (Brackin, 1903)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Cross-Hole Countersinks: A Slanting Hole Through the Cone Makes One Spiral Shearing Lip (Taylor, 1903)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Threaded-Stud Rubber-Head Hammer: Heads Screw Onto the Body's Own Studs and Lock the Handle's Nail In (Dicks, 1951)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)
na Forge
Ubucuzi bw'Ibyuma
0
0
0
0
0
0
Laminated Rubber Mallet: A Rubber-and-Canvas Head Locked on a Flared Handle by an Internal Rib (Whisler, 1924)
na Forge
Ububaji
0
0
0
0
0
0
Laminate Bevel Trimmer: Two Pads at Right Angles Hold a Small Router at 45 Degrees on a Corner (Roche, 1971)
na Forge
Ububaji
0
0
0
0
0
0
Rack-and-Pinion Router With a Zero-Set Knob: Two Knobs on One Hollow Pinion, Set to Zero on the Work (Rees, 1969)
na Forge
Ububaji
0
0
0
0
0
0
Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)
na Forge
Industry 3.0 — Assembly Line & Mass Production (1913)
1
0
0
0
0
0
Rack-and-Pawl Plunge Router: The Motor Rides One Post on a Spring and Steps Down a Tooth at a Time (Carter, 1925)
na Forge
Ububaji
1
0
0
0
0
0
Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)
na Forge
Ububaji
1
0
0
0
0
0
Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)
na Forge
Ububaji
1
0
0
0
0
0
Sliding-Table Saw That Switches Itself: A Hand Saw Under a Table on Balls, Turned On and Off by the Stroke (Tracy, 1941)
na Forge
Ububaji
0
0
0
0
0
0
Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)
na Forge
Ububaji
0
0
0
0
0
0
Portable Bench Saw: A Lift-Out Power Unit on Trunnions, Its Motor on Spring Bars, Under a Tilting Platform (Henkel, 1928)
na Forge
Ububaji
1
0
0
0
0
0
Hagaragajwe 24 kuri 2500