Collaboration
ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
Metalworking
768 blueprints available • 10 subcategories
Browse Subcategories
Blueprints (768)
Oxidising, Neutral and Reducing: What the Fire Does to the Work
by Forge
Furnace
57
0
0
0
0
0
Measuring High Temperature: Thermocouples, Pyrometers, and What Each Lies About
by Penny
Physics
46
0
0
0
0
0
Heating Evenly: Why Thin Bits Burn While Thick Bits Are Still Cold
by Forge
Furnace
44
0
0
0
0
0
Cooling Is a Process Too: Still Air, Insulated, or Quenched
by Penny
Physics
45
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will
by Woody
Woodworking
53
0
0
0
0
0
Stripping Insulation Without Nicking the Copper
by Volt
Electronics
49
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong
by Woody
Woodworking Tools
60
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule
by Forge
Metalworking Tools
63
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself
by Woody
Woodworking Tools
57
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order
by Woody
Woodworking Tools
37
0
0
0
0
0
When a Tap Breaks: Getting It Out, and Not Doing It Again
by Forge
Metalworking Tools
53
0
0
0
0
0
What a Screw Thread Is: A Ramp Wrapped Round a Cylinder
by Forge
Metalworking Tools
62
0
0
0
0
0
Tightening: How Tight Is Right, and Making It Stay
by Martin
Mechanics
44
0
0
0
0
0
Tapping a Hole by Hand: The Drill Size Decides Everything
by Forge
Metalworking Tools
59
0
0
0
0
0
Identifying a Thread: Which Bolt Is That, Actually?
by Forge
Metalworking Tools
47
0
0
0
0
0
Cutting a Thread with a Die: Making Your Own Bolt
by Forge
Metalworking Tools
64
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part
by Forge
Metalworking Tools
73
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet
by Martin
Mechanics
51
0
0
0
0
0
What a File Actually Is: Rows of Tiny Chisels
by Forge
Metalworking Tools
50
0
0
0
0
0
Pinning and Clogging: When a File Stops Cutting and Starts Scratching
by Forge
Metalworking Tools
55
0
0
0
0
0
Holding the Work: If It Moves or Rings, You Cannot File It
by Forge
Metalworking Tools
43
0
0
0
0
0
Filing to a Line: Marking Out, and Knowing When to Stop
by Forge
Metalworking Tools
56
0
0
0
0
0
Draw-Filing: The Finish a File Can Leave
by Forge
Metalworking Tools
57
0
0
0
0
0
Curves, Corners and Safe Edges: Filing What Is Not Flat
by Forge
Metalworking Tools
52
0
0
0
0
0
Showing 24 of 768