IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Àwọn Irinṣẹ́ Iṣẹ́ Igi
Ìtọ́nisọ́nà 47 wà
Àwọn Ìtọ́nisọ́nà (47)
Fit: A Joint That Needs a Mallet Is Too Tight
láti ọwọ́ Woody
Iṣẹ́ Igi
35
0
0
0
0
0
Dovetails: Why They Point One Way, and What That Buys You
láti ọwọ́ Woody
Iṣẹ́ Igi
28
0
0
0
0
0
The Mortise and Tenon: What Each Part of It Is Actually For
láti ọwọ́ Woody
Iṣẹ́ Igi
31
0
0
0
0
0
Why a Butt Joint Fails: End Grain Does Not Glue
láti ọwọ́ Woody
Iṣẹ́ Igi
32
0
0
0
0
0
Twist, Cup and Bow: Winding Sticks Make the Invisible Obvious
láti ọwọ́ Woody
Iṣẹ́ Igi
39
0
0
0
0
0
The Marking Gauge: Distance From a Surface, Not a Number
láti ọwọ́ Woody
Iṣẹ́ Igi
23
0
0
0
0
0
The Knife Line: A Mark You Can Put a Chisel Into
láti ọwọ́ Woody
Iṣẹ́ Igi
34
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will
láti ọwọ́ Woody
Iṣẹ́ Igi
31
0
0
0
0
0
Face Side and Face Edge: Everything Is Measured From the Same Two Surfaces
láti ọwọ́ Woody
Iṣẹ́ Igi
27
0
0
0
0
0
Dividers: Laying Out Without Measuring Anything At All
láti ọwọ́ Woody
Iṣẹ́ Igi
26
0
0
0
0
0
Cumulative Error: Why You Measure From One End, Not Piece to Piece
láti ọwọ́ Mark
Iṣẹ́ Igi
25
0
0
0
0
0
Which Clamp: What Each Type Is For, and Making Your Own
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
27
0
0
0
0
0
The Dry Run: Assemble It Once With No Glue at All
láti ọwọ́ Woody
Iṣẹ́ Igi
26
0
0
0
0
0
Clamping Pressure: Enough, Even, and Not Too Much
láti ọwọ́ Woody
Iṣẹ́ Igi
42
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
36
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
34
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
32
0
0
0
0
0
Starting a Cut: The First Three Strokes Decide the Rest
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
29
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
20
0
0
0
0
0
Sawing Square: Two Lines at Once, and Fixing a Cut That Drifts
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
39
0
0
0
0
0
Sawing a Curve: Coping, Fret and Bow Saws
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
30
0
0
0
0
0
Rip and Crosscut: Two Saws Because Wood Has a Grain
láti ọwọ́ Woody
Àwọn Irinṣẹ́ Iṣẹ́ Igi
31
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part
láti ọwọ́ Forge
Àwọn Irinṣẹ́ Irin
36
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet
láti ọwọ́ Martin
Ìmọ̀ Ẹ̀rọ
37
0
0
0
0
0
Ń fi 24 nínú 47 hàn